Question about Maytag 22 Cycles Topload washer, SAV365Z

2 Answers

Pull knob--nothing happens.

Matag washing machine will not start. I set the dial and pull the knob and nothing happens at all. Sensor? Thanks OH

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There is a fuse in the machine, usually at the front of the machine when you take off the cover. Check for blown fuse, and replace it.

Posted on May 03, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 686 Answers

TIMER

Posted on Apr 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I pull the knob to do a regular wash and nothing happens, no water no agitation. However, when I turn the knob to rinse it that works. This suddenly happened, was working before. Is it the knob?


Rinse on most washers is cold water your wash cycles can be cold hot and even warm. Problem You may have is a bad water feed valve Or Timer and possible bad wire harness at motor to timer
check water valve Turn washer to regular wash cycle pull knob on will washer fill ?
if water starts to fill then change washer temp if washer has this.
if water comes out on all settings water valve is fine.
Check the water both hot and cold that it is turned on;at faucet.
Your Kenmore Most likely has a bad water valve check for hot water side clog or not working.

Apr 25, 2015 | Kenmore 2982 800 3.5 cu. ft. Top Load...

1 Answer

Maytag stacked unit LSE7806ACE. dryer is fine , the washer will not fill or run, if I manually turn the timer to drain the tub spins and the lid switch works fine. But the unit won't do anything f


You have a timer problem, the contacts are welded in spin mode.
This is almost always caused by advancing the timer by hand when the dial is pulled out in the "ON" position, causing arcing of the contacts.

Sep 22, 2017 | Maytag LSE7806A Top Load Stacked...

1 Answer

Cannot set Control dial for wash cycle. Knob will not move indicator dial. Rotating without engaging indicator. Thanks


Pull the center knob strait off. I suspect the center shaft of the knob is broken. If it is order a new knob but before replacing it make sure the shaft on the timer does not have a metal sleeve from the knob remaining on the timer shaft. Temporarily you can try to use needle nose pliers to turn the shaft to see if the washer works.

Aug 21, 2010 | Washing Machines

1 Answer

The dial doesn't turn with the knob pushed in, when we go to set the wash. but it does move manually with finger tips


The teeth on the knob are probably gone. To pull the knob off remove the clip between the knob and the dial and pull knob off.

Mar 01, 2010 | GE WBSR3140DW Top Load Washer

2 Answers

GE Spacemaker Washer/Dryer wont start only washer or only dryer


Did you figure out a solution to this problem? I just bought a brand new Frigidaire and it is doing the exact same thing, except it never worked properly. I thought it was the unit and had HH Greg bring another out but the 2nd one did the same as the first.

Feb 09, 2010 | GE WSM2700W Unitized Spacemaker Washer and...

1 Answer

The machine won't start... it's been working fine


You don't give the model or any info. If it is "older" chances are you need a new settings knob or can clean the contacts inside if you are capable of removing it. Other than that check the obvious like cord/plug, spin button, that type of thing.

Feb 08, 2010 | Kenmore Washing Machines

1 Answer

Kenmore 600 with atc. water temp change


to change water temp when a cycle has started, pull the knob and reset the water temp, then move the dial to the desired setting. push knob in. resolved by trial and error!

Nov 05, 2009 | Maytag MAV5920E Top Load Washer

1 Answer

No hot or warm wash cycle


If you suspect you have a defective timer it can easily be replaced by performing the following steps:


1. Unplug washing machine... and pull out the timer knob. Some knobs have a removeable center cap and hidden screw. Some are simply slip-fit. Remove the knob.

2. Remove console. This can be accomplished in one of two ways depending on which type of console you have.

a. If the console has removable end caps, the caps lift off by prying on the top from the back of the washer.
The cap will pull off towards you as you are facing the unit from the front of the washer.
There will be a screw under each end cap that you will need to remove.


b. If the console does not have removable end caps, you will need to slide a putty knife under the front corner of each side and push in while lifting up.
There is a retaining clip under each side that has to be released.


3. Once the console has been released it will lift up and fold back over the back of the washer in its resting position. Use care not to stress the small plastic hinges that hold it on. They can break easily.

4. Disconnect all power plugs and remove the timer's mounting screws.

5. Reinstall reverse of removal.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jan 24, 2009 | Washing Machines

1 Answer

Control knob will not turn to desired setting


the timer knob has a clip that will allow you to remove the knob from the timer. it is between the knob and the dial. what happens is the knob has gear like teeth that will become stripped out.it is easy to replace but alittle hard to remove. you need to get a small screwdriver and go behind the knob, pull on it alittle and you will see the clip, then use the screwdriver to push the clip out of the knob, then the knob will pull of and you can replace it.

Dec 28, 2008 | GE WJRR4170E Top Load Washer

2 Answers

Hard to start dryer, control know loose/misaligned


your saying that pulling the timer knob out, which normally starts dryer, does nothing. however if you pull out and apply pressure upwards on knob and touch nothing else, the dryer will start??? if the thats the case sounds like a short in the timer mechanism , youll need to replace the timer assy

Mar 18, 2008 | Maytag Atlantis MAV6451 Top Load Washer

Not finding what you are looking for?
Maytag 22 Cycles Topload washer, SAV365Z Logo

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...