- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Hi there!!
Try this:
Step 1
Turn the component, like a TV set, on.
Step 2
Hold down the "Code Search" key on the SystemLink 3 remote until the light that's on the remote turns on. Keep holding the button after the light turns on.
Step 3
Press the device button ("TV" button) at the top of the RCA remote. Then, release both buttons.
Step 4
Press "Off/On" repeatedly as the remote browses through available codes. Continue doing this until the component shuts off.
Press "Enter" to save the code.
Good Luck!
Mr.Mike
FL231. FUSE.... The RCA ITC222 chasis has a common problem. and it not all that difficult to repair. Does your rca projection tv have read blue and green shadows? Does it have bowing in affect on the top and bottom of picture? when you turn it on does some thin red green and blue line bow in from the top then go away. The main question to determine if you have the fl231 fuse problem is if you go into customer menu then setup do you have the "CONVERGENCE' option. If you do not. then i suspect you have this problem. In the manufactering of these sets Lead free solder is used. now there is great debate over the use of lead free. connection tend to be more brittle. cracks develop around the solder connections of the high voltage flyback transformer. this very small crack set up oscillations in the cuicit with a 400 milliamp fuse. THis fuse cant take it. When this fuse blows the processor then does not know its a projection tv with three projection tubes. it thinks its a crt tube tv. and crt tube tv dont need "convergence" so it removes the convergence from the set.
TO REPAIR... 1. Warning. this set can generate leathal dangerous voltages even unplug do not attempt if you have no experence with electronics. 2. Remove the back. there a number of torx 20 screws. 3. what you will see is a number of circit boards There will be one on the right and one on the left. the one on the right is the small signal board. the one on the left is called the power deflection board. it has a large black part with a big red or black wire coming from the top, this is the flyback.Next to the flyback on the right of it there will be three small rectangular componets tan or brown in color. these are fuses. the one in the middle is the fl231 fuse. 4. getting to this fuse can be difficult. these two cuicit boards sit on a tray that is removable. to remove this tray it is pulled out and up. BUt watch the wires.loosen the wire tyes. 5 when you get the tray up the bottom side of the board can be accessed you will now have to unsolder that fuse. one side of this fuse is under a plastic part of the tray. i have found the easest way is to cut away the plastic to get to it. if you dont want to do this you will have to remove the board. only remove half of the plastic brace 6. REPLACE FUSE RCA PART 259213 7 RESOLDER FLYBACK CONNECTIONS simply heat up and add a little solder 8 reassemble set. make sure you examine the set for loose connections. 9 and remember "BE Careful'
You should make sure you have an active internet connection and that the tv is in a spot that is not receiving interference. Are you able to select any apps? what do the say when you try and use them? Did anything happen prior to the apps not working?
Main chroma processor IC fault. Replace it. Contact any service technician. If you wish to get some details; visit the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
if it has aux input rca's, then go to an electronics or car audio shop and buy a "stereo rca to 3.5mm headphone jack adapter cable" This will then plug into the headphone jack on the ipod.
0704,0002,0406,0007,0011,0611,0811,0312,0514,0720,0102, 0502,0601
08 17,0917,0835,0901,0103,0803,0211,0912,0114,0519,0320,0420
Estos son todos buena suerte.,
×