Question about Mtd Bronco Rear Tine Tiller

1 Answer

Tines wont turn

Bought used tiller mtd model 210-031-000. Tines had alot of play and worked fine for 30 min. before tines quit. What parts and cost am i looking at?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Without really knowing what is broken it will be tough to give a firm idea of the cost. However, you can head over to www.partstree.com. They have a great detailed parts break down and costs associated with it. Looked up your part numer and can find at this link: http://www.partstree.com/parts/?lc=mtd&mn=210-031-000+%281990%29

Posted on May 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just bought an older Mantis 2 cycle tiller. The tines engage when the tiller is started. Of course that makes it hard to start with the tines on the ground! I don't believe it was doing this when I...


if the idle is too high the tines wont stop due to the tiller tines are run by a "centrifuigual clutch" which means when you increase the throttle speed the tines will start to turn : there are 2 adjustments you can try,1) adjust the idle screw under the carburetor where the throttle adjustment and a triangle piece of metal touch(your throttle cable wire will be attached to this triangle) ,if the triangle and idle adjustment don't touch and there's a gap between these 2 pieces close the gap by adjusting the 10mm adjusting nut,this will correctly set the idle #2) adjust the idle adjustment screw talked about above till the tines dont turn with throttle set at idle or lowest speed setting

Mar 26, 2011 | Mantis 2-Cycle Tiller

1 Answer

Have a MTD Yard Machine rear tine tiller Model 410 and when I went to use it this year when I put it in gear the tines did not move. I called the MTD tech and he said it sounds like its in the...


It is the shift fork in the transmission. Bad part design and if you plan to take it apart, use sandpaper and really clean the wheel axle and tine axle before you take it apart.

Mar 20, 2011 | Mtd Garden

1 Answer

Tines will not turn when engeged. made a grinding


It sounds like a problem with the drive pulley on the engine to me. Maybe the key is striped.

May 27, 2010 | Mtd Troy-Bilt Bronco OHV Tiller

2 Answers

Mtd rear tines tiller won't engage tines. F and R


I had similar problem recently with 2007 Huskee MTD series 410. The shift assembly bent and couldn't move the clutch collar all the way over on the drive shaft.

4395dea.jpg

Apr 23, 2010 | Mtd Products Yard Machines 158CC Tiller

1 Answer

Tiller goes For./Rev. but wont drive forward with tines engaged


check the sher bolt on the tine to drive shaft. ill need model and ser number off the unit before i can go further with helping you thy changed them around a lot

Oct 09, 2009 | Mtd Garden

2 Answers

Honda FG100 Tiller - Tines wont move


I took the transmission apart and the gears were fine. The friction pads on the centrifugal clutch don't seem to make full contact with the drum. Does anyone know what the thickness of the friction pads are suppose to be? I used some belt dressing on the pads and got some movement on the tines. With no wear on the gears, I guess I'll be replacing the clutch.

May 02, 2009 | Honda Hmantis Mantis Garden Tiller with...

1 Answer

Belt seems to be slipping


good evening. I would suggest checking the tine bearings as well alignment. I had (have) a 2003 mtd rear tine which blew the entire bearing box for the second time. The times should have little to no flex when push or pulled. Fortunately, MTD came good for the first rebuild even though my warranty had expired...they covered the parts and labour was all mine. If the tines seem properly working, possibly try out this website to get the 100% correct belt....hope this helps.

http://www.milacalawn.com/parts.asp

Apr 17, 2009 | Troy Bilt, Tuffy, Rear - Tine Tiller, 4.0...

1 Answer

MTD yard machine model#216-410-000


either your tine shaft is seized to bushings which requires total dissassembly of unit or you have a failure of drive chain or gear i'm currently repairing one with the seized bushings if you are not a technician i would recomend replaceing unit very costly to repair in any case.

Apr 05, 2009 | Mtd Products Yard Machines 158CC Tiller

1 Answer

Broken clutch cable connector, MTD Tiller


I found micro fiche on jackssmallengines.com . Click on the manufacturer's tab at the top of the page then you'll have the option to use an off-site tool to locate your machine. I used it and found my 1990 mtd rear tine tiller. I needed the cable that engages the tines - maybe the same as you. The part number for my 1990 model's cable was 746-0535. Dont know if it was still the same in 96 to 98. But look at the fiche and see.

Apr 04, 2009 | Mtd Products Yard Machines 158CC Tiller

Not finding what you are looking for?
Mtd Bronco Rear Tine Tiller Logo

Related Topics:

667 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mtd Garden Experts

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Tim Whalen

Level 3 Expert

3072 Answers

Phil Walker
Phil Walker

Level 3 Expert

605 Answers

Are you a Mtd Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...