Question about Sanyo DRW-500 DVD Recorder

1 Answer

No Power It had power last night and this morning and now it will not turn on. There was no power outages and my other electronics are working fine they are all on a power surge device. Any clues? Thanks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,074 Answers

The power supply of your dvd is not working this is controlled by a few diodes and a regulator the power cord is attached on to the power supply.if you do not have the experience to repair electronics set have a tech look on your dvd.good luck

Posted on Jan 06, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Cant get the power to turn on,worked fine last night, it got unplugged, this morning plugged in, won't turn on and the power button just flashse

Flashing is either an error code or the set trying to boot up--some of the Mitsubishi sets if power removed will blink for a minute and then stop--then the set can be turned on.

a model number?

Apr 28, 2012 | Mitsubishi Televison & Video

1 Answer

My xbo was working last night and we had a power outage , then this morning when i check if any electronics r working , everything was fine but when i went turn on my xbox it is stuck on standby mode and...

It sounds like it may have had a power surge. Was it plugged into a power strip, or straight into the outlet? If it was in the outlet, or if the power strip is old, it may not have been protected and you could have fried some of the internal components. Also, did you have an ethernet cable plugged into it? My Xbox got fried a few years ago because of a power surge through my router. If the internal components are broken, the only reliable place to send it, in my opinion at least, is Microsoft's own repair site.

May 14, 2011 | Microsoft Xbox 360 Console

2 Answers

Last night the tv was fine i turned it on this

Unplug 20 minutes. Make sure there is adequate ventilation around the set.

Try with the original manufacturer remote to view setup menu.

Power outages come at night. This sometimes resets the TV and other devices. .

Mar 25, 2010 | Insignia 42" LCD Flat-Panel HDTV

1 Answer

We lost power last night and this morning the maytag jet clean dishwasher is not working, does not appear to have any power. Is there an internal circuit or something?

there are internal thermostats or even an internal type fuse kit..... it is also common after power outages when you regain power that , that sudden jolt of electricity enters or circuits again it blows out electronics.... if u have an electronic control you might have blown that control board as well hope this helps

Jan 31, 2010 | Maytag MDB9600A Jetclean II Built-in...

1 Answer

How to replace power supply?

Toshiba model 57H93 worked perfectly last night. Turned off and went to bed. Turned on this morning, and nothing, it won't turn on. Checked all cords and cables, pushed reset button, and still won't turn on. What could cause this to happen?

Dec 14, 2009 | Toshiba 57H93 57" Rear Projection HDTV

1 Answer

My Vip622 was down this morning, no power outage,

Unplug the unit from the mains for at least an hour, then plug it back in again and try to boot it up.

Good luck

Jun 19, 2009 | DISH Network ViP622 DVR DTV Receiver /...

1 Answer

Tv wont turn on worked fine last night

If there is no power at all, then the problem is likely the power supply unit.
The PSU must be tested, then eventually replaced.

May 30, 2009 | Spectroniq PLTV3250 32 in. LCD TV

1 Answer

No display

Your minitors power supply is now damaged, probably from the power outage. I t will need to be repaired or replaced. Check the cost and benifits of both options and make a discision.

Jul 30, 2008 | Acer AL1912 19" LCD Monitor

Not finding what you are looking for?
Sanyo DRW-500 DVD Recorder Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sanyo Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75025 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers


Level 3 Expert

5318 Answers

Are you a Sanyo Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides