Question about Senco Tools & Hardware - Others

1 Answer

NEED PARTS BOOK AND PARTS FOR A SENCO-MATIC MODEL SNI FINNISH NAILER PAT NO.2.983.922 3.170.487 3.278.102 3.278.104 M3/15/78

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 718 Answers

I think you are referring to model SN1 (SN-1);

Get parts list from;

and order parts from your local dealer.

Posted on Apr 15, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My senco F16 finisher nailer quit. It has been used very little. The light comes on but does not fire. Suggestions?

being you say light comes on my guess is it is electric so i will try to help based on the electric model. here is a link to the f16s fusion 18volt model hope this help you figure the rest out.
Fusion 16S
this link is to the main page copie this one if the first one fails you. good luck

Nov 06, 2017 | Senco Air Tools & Compressors

1 Answer

The trigger on my senco 502 nailer will not compress, ie will not fire. Why and what parts if any do I need.

Check the manual if you have a safety switch. Also check for any bent nails inside the gun. Make sure all is OFF before investigating.

Oct 12, 2016 | Senco 4D0001N Framepro 502 Framing Nailer

1 Answer

Air leakage from bottom & no return

The internal workings of a pneumatic nailer are fairly simple and easy to diagnose problems. If you go to Senco's website at, you can find a breakdown of what parts are where inside your nailer. Remove the four bolts holding the cap on and check the condition of the o-rings inside the gun. They are the most likely failure point for your tool. Senco does make repair kits that contain all the wear items in your nailgun. It will be listed on the parts breakdown and can be bought at most online parts stores or places like eBay and Amazon.

Dec 26, 2012 | Senco FP18 FinishPro 18 - Gauge Brad...

1 Answer

Senco trigger schematic

Go to the Senco website at, click on the "Parts Charts/Specs/Manuals" tab at the top then scroll down to Frame Pro 502 where you can view or download the manual or parts guide. Their parts guides have very good exploded views of the tools and are very helpful when reassembling them.

Oct 25, 2012 | Senco 4D0001N Framepro 502 Framing Nailer

1 Answer

I have a senco coil roof nailer that all of a sudden is leaking air big time and will not coil and fire nails. What parts do I need to replace.

depends on where the air is leaking from. If you go to and type in your model number you can look at a breakdown and they will list the rebuild kits specific to the leakage, they make an upper o ring kit and a lower kit for this problem. Let me know if you need more assistance or where the air is leaking along with the model number and I will find a number for the rebuild kit. Also the senco kits have detailed instructions on how to install them.

Apr 04, 2011 | Senco Tools & Hardware - Others

1 Answer

Air nailer vnot operating. blowing air from top close to handle

Your nailer has worn or broken o-rings in the top end. You need a rebuild kit (Senco part number YK0360) to get your gun going again. They are available through most online, after market parts stores. When you get it, remove and replace each seal and o-ring one at a time so you get them all back in their proper place and use all of the grease to lube the o-rings. Use all of the parts in the kit, if one o-ring or seal is damaged the others are not far from failing.

Jan 25, 2011 | Senco FP620 Framepro 602 2" - 3 - 1/2"...

1 Answer

Do i need to buy piston driver assembly or can i by just the driver blade

These new Senco FinishPro tools are chinese made and unlike the old US made tools, you need to buy what's termed a 'piston driver unit'. It should be fairly cheap though, compared to old Senco parts.

Jan 17, 2011 | Senco Finishpro 15 Finish Nailer & Sls15...

1 Answer

Air leak top of gun senco oil less coil nailer scw40r. unclehhotmail.comowd@

Nailer scn40r is an oil less coil roofing nailer. If it will not fire and leaks out head then most likely problem is diaphragm torn or pinhole. Replace firing valve part # BAO120 for good as new operation.
Order parts from

Oct 16, 2010 | Senco Tools & Hardware - Others

1 Answer

I have an older model senco finish nailer that continuously blows air out the exhaust what is the problem?

probably a split or stuck o ring. You can go to and download a breakdown and purchase a rebuild kit for this tool.

Mar 27, 2010 | Senco Finishpro 15 Finish Nailer & Sls15...

3 Answers

SENCO SHF 50 floor nailer won't consistently sink cleats

Some Senco tools reqire oil.  there is oil specially designed for tools. 

Aug 01, 2009 | Senco SHF50 2" Hardwood Flooring Nailer...

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

769 people viewed this question

Ask a Question

Usually answered in minutes!

Top Senco Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1388 Answers


Level 2 Expert

131 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

297 Answers

Are you a Senco Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides