Question about Cooper Wiring Devices Motion Sensing Switch- 30 Feet

1 Answer

I changed light switch and fan switch quit working. The fan switch is its own station and then the light switch is on its own station right beside each other

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cooper Wirin... Master
  • 5,353 Answers

Did you take photo of wiring before disconnecting old switch...you might have wired wrong.
Rewire old switch and see if same problem exists.
Check that new switch is rated for same device.
Attach 2 photos of old and new switches, each wired...so expert can see problem better.
http://waterheatertimer.org/How-to-wire-switches.html

Test that fan switch is getting power.

Gene

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Posted on Sep 15, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Guys, I have a CDX GT610, the issue is that is


hi marco, the problem seems with the switches on the face. make sure that ALL switches have a "click" sound when pressed down. if not then that switch needs to be replaced. faulty switches can cause the face functions to work erratically. to try another route use your unit with the wireless remote control to check if all functions work well. cheers.

Sep 06, 2013 | Sony CDX-GT610Ui CD Player

1 Answer

Remote quit working for litex ceiling fan


after changing the batteries make sure you didn't change the remote code. If you didn't there should be a reset button inside the battery compartment, it may just look like a small hole. Just use a toothpick and insert it into the hole and lightly depress the reset switch.Replace the battery cover and try using the remote again.

Apr 13, 2012 | Casablanca Fan Dryers

1 Answer

I just installed a 52"


yes this is because the dimer is giving the light less power.you just need to change the switch to a single switch then your dimer will work right all the time. good luck

Aug 12, 2011 | Hunter 52" Ceiling Fan With Light And...

1 Answer

Brake light switch for 1998 ford escort station wagon


Common problem with these cars are that the rubber piece that "gaps" your brakepedal from the micro-switch keeps breaking (they usually have a replacement rubber piece connected on the brake pedal beside it). If your brake lights won't go off because of this, either change-out this rubber gap piece - or, you can just change the gap with a wrench, and not even use the rubber gap piece (this is what I ended up doing on a couple of my escorts).

Aug 02, 2010 | 1998 Ford Escort

1 Answer

1989 Buick Park Ave heating problems. I got this car a few months ago and it was great,...now having problems. The heating/AC control unit works fine, there was however a toggle switch controling the...


check to see if there is a resistor on the blower motor. it should be located either beside or underneath the blower motor.. if that is bad it wont let you select different fan speed settings and if it goes completely out the blower will not work at all.

Feb 12, 2010 | 1989 Buick Park Avenue

1 Answer

My ceiling fan isnt working right


dont you have a three position pull switch on the unit like a three-way light bulb or if you have a remote controlled fan it should have it on the remote control

Sep 24, 2009 | Encon Industries (78018) Ceiling Fan

1 Answer

Hp designjet 500 does not work


You probably have a problem with dry ink in the service station. This is the "tank"on the right hand side of the plotter which collects all your wasre ink. I would have a guess that because of the long standing period this has dried and is preventing the station from moving and cleaning the heads. You will have to remove the right hand cover of the machine, then looking directly downwards just behind te display panel you will see two torx screws, loosen them. The service station can then be removed and cleaned. Be sure to disconnect the small plug on the service station motor and fan, also remove the motor and fan before cleaning the station with water under a tap. BEWARE this is a really messy job, your hands will be black (use dishwashing gloves) and it takes a really long time to clean it properly, wait for it to dry in the sun and re- assemble.
Good Luck
Dave

May 04, 2009 | Office Equipment & Supplies

Not finding what you are looking for?
Cooper Wiring Devices Motion Sensing Switch- 30 Feet Logo

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cooper Wiring Devices Electrical Supplies Experts

William Erickson

Level 2 Expert

47 Answers

Harvey Hyde

Level 2 Expert

153 Answers

Brad Brown

Level 3 Expert

18060 Answers

Are you a Cooper Wiring Devices Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...