Question about McCulloch Garden

1 Answer

What is the oil-gas ratio and the bar oil for a Mc Culloch Mac130

I am looking for a manuel so I can find out what the oil to gas ratio is, as well as what the bar oil is for a Mc Culloch Mac130 chainsaw.

Posted by on

  • Anonymous Mar 13, 2014

    Mc culloch 484 chainsaw fuel mix

  • Anonymous Mar 13, 2014

    Mc culloch 484 chainsaw fuel mix

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 263 Answers

You should be safe with a 32:1 mixture unless you are a logger. And any Bar Chain Oil should work fine.

Posted on Apr 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What kind of oil do i use in a mc culloch se250 chainsaw


You should use a good quaility two stroke oil mixed at 25-1 in the fuel tank, and a non fling chain oil in the chain lubrication tank.

Jul 08, 2012 | Garden

1 Answer

What's the oil/gas mix ratio on a Mac130.. and also what are the factory/normal settings on the high/low carb adjustments screws.


Run it at 25-1 with a good two stroke oil, base settings are 1 turn on the high and 1 1/4 on the low, you will need to fine tune from there.

Jun 15, 2011 | McCulloch 16 Inch Gas Chain Saw MCC1635AK

1 Answer

Mc culloch tm 250 strimmer. petrol/oil ratio


40 parts fuel to 1 part 2/stroke oil

Aug 05, 2010 | Garden

1 Answer

What are the carb. adjs. on a Mc culloch chain saw model cs 38em


If it bogs down like it's getting too much fuel, turn the low side screw out about 1/8 of a turn at a time until it will rev without bogging. If it chokes down like it's not getting any fuel, you probably need to open up the high screw a little.

BTW, you can determine which screw is which by looking at the carb at the base of the screw...it will have a L for Low or H for High stamped near it.

Jul 18, 2010 | McCulloch Garden

1 Answer

Clutch cover smoking


Remove the bar and chain and wash out the clutch internals with spray carburetor cleaner. Clean the side of the engine case, start the engine and watch for oil oozing out of the side port. Clean the bar drive-end small oil passages that go out to the chain groove on each side and clean the entire chain groove. If oil came out of the engine side port ok, then re-assemble the bar and chain, but leave the cover fasteners only finger tight. Tighten the chain so that the chain comes up to the bar, but not so tight that the chain can't be pulled by hand. Tighten the cover fasteners and recheck the chain tension. Make sure the chain teeth cut toward you on the bottom run and that the chain is properly sharpened. Hope this helps!

Jul 05, 2010 | McCulloch Garden

1 Answer

Mc culloch chain saw 742 manual need urgently


Both the OM and IPL can be found here:
http://www.mcculloch.biz/int/support/owners-manuals/
Just type "742" in the "Model Search" window and click Search. HTH
Lou

Feb 17, 2010 | McCulloch Garden

1 Answer

After having my Mc Culloch sharpened


You may have the chain on backward. The teeth on the bottom of the bar have to have the sharp edge coming at you in order to cut anything. Hope this helps you, Jeepfxr

Jan 28, 2010 | Garden

1 Answer

Como graduar salida de aceite dela cadena de la motosierra mc culloch pm 484


I think you want the oil/fuel ratio; 50:1
Fuel/Oil Mixture
  1. Use a quality 2 cycle oil and mix it to the OIL supplier's recommended ratio. Today I use Stihl 2 cycle oil mixed @ 50:1 in a Pioneer that I purchased new in 1980. There are no gouges or scratches on the piston or cylinder and I have no carbon build up on the piston top. The manual (on stone tablets) recommends 24:1. Over the years the mixture has leaned from 24:1 (Saw Recommendation) to 28:1 (Lawn boy mower recommendation) to 32:1 (Oil provider 8oz/2gal - used for many years) and finally the last 5 (±) years 50:1 (Stihl 2.6oz/1gal)
  2. Any fuel containing ethanol is not good with chainsaws. Mix what you expect to use within a few months. Anything over 1.5 months old use up in a 4 cycle engine. HTH
Lou

Nov 03, 2009 | McCulloch 10" Electric Pole / Chain Saw

Not finding what you are looking for?
Garden Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top McCulloch Garden Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

roeb

Level 2 Expert

263 Answers

Are you a McCulloch Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...