Question about Craftsman Gas Mini - Tiller/Edger

1 Answer

I have a craftsman mini tiller 10" model no:536.79500 I"m in need of part no:56159 -Shaft /Gear long Do you know where i can get one. My serial no is 500534534 P.S --- I can press a New Gear on if I can get one !!! Thanks, Rich

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You can buy the shaft and gear combo at Searspartsdirect.com for 75.00 plus shipping. I can't find just the gear and I have looked.

Posted on Jun 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sears mini tiller 10


it could be the bowl nut gasket or the bowl oring either could be dried out or in the case of the bowl oring could be pinched

Apr 03, 2012 | Craftsman Gas Mini - Tiller/Edger

1 Answer

I own a 2 cycle mini tiller craftsman and I need a manual for it. I want to tune up tiller it's blowing smoke.


Manuals for many Craftsman tools are available here: http://www.managemylife.com/mmh/owner_manuals . Lots of tillers are listed just by searching for Craftsman tiller. If you can find the model number (usually on a plaque on the housing of the tiller), you can narrow down the list greatly.

I hope this helps.

Cindy Wells

Mar 31, 2011 | Mtd Craftsman 4Cycle Mini Tiller

1 Answer

I have a Craftsman 17" rear tine tiller with


check to see if there is a snap ring on the shaft or a roll pin.

Feb 23, 2011 | Craftsman Garden

1 Answer

Cannot find the model number of our Craftsman Mini Tiller edger


The model number is on a metalized label usually on the upper shaft of the tiller. On the tillers it is usually black with silver letters.
Some of them have the label on the motor itself and some others have the label on the lower guard.

Jan 04, 2011 | Garden

1 Answer

I need to change the gear shift that broke off in the transmission do i have to split it open all the way to change it


Craftsman tillers usually use a chain drive transmission. Sears does not usually offer individual parts for these transmission. They want you to replace the entire trans assembly. If the gear shaft is available (www.searspartsdirect.com) , then yeas, you would have to split the case all the way open to replace it. This is not an easy job. Most major repair shops would charge 4 or 5 hours of shop time for this repair. It generally requires complete dissassembly of the tiller to remove the transmission.

You did not give a model # for your tiller, so I am only giving you general solutions. Please look up the parts. Many times it is more cost effective to replace your tiller than it is to repair it. Remember that all of the other gear shafts are the same age as the one that broke and have been through the same stresses.

Good luck!

Jan 04, 2011 | Craftsman Garden

2 Answers

Craftsman mini tiller


Craftsman mini tiller. Are you selling this unit, giving it away or what. Your information is somewhat meager to say the least.

May 28, 2010 | Craftsman Gas Mini - Tiller/Edger

1 Answer

Roto tiller won't start - primer bulb


Carburetor needs to be rebuilt or replaced. Replaced would be my choice.

May 23, 2009 | Craftsman Gas Mini - Tiller/Edger

3 Answers

Oil seal for rear tine shaft


The serial number is located on a flat spot just above the right wheel shaft where the gear housing and the top gear cover meet. It will be a six digit number stamped in the metal.

Frank

Mar 11, 2009 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

Not finding what you are looking for?
Craftsman Gas Mini - Tiller/Edger Logo

Related Topics:

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Craftsman Garden Experts

Wade Mobley
Wade Mobley

Level 3 Expert

475 Answers

Dean Gruber

Level 2 Expert

110 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Craftsman Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...