Question about Mitsubishi VS-45607 45" Rear Projection Television

2 Answers

No power I have 2 tvs with no power. When I pushed the power button it start and shuts off. I can hear the high voltage noise. I replaced the Vertical IC and the regulator IC not good yet. I'm despending lot of time on these tvs. Please help me if you can. Thanks

Posted by on

  • Josias Aleixo
    Josias Aleixo Sep 27, 2007

    Thank you for your help. This information halp me solver my problem. Thanks

  • Josias Aleixo
    Josias Aleixo Oct 09, 2007

    I got the code. Vertical problem, I replaced the vertical IC still some, then I did tests on vartical circuit eventhing was fine, the I checked the signal board, it had problem, the I replaced the signal board now the tv is working fine. Thank you help

×

Ad

2 Answers

This does not fix my tv

Posted on Jan 08, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,153 Answers

This model is equipped with a self-diagnosis feature to help with diagnosis of shutdown problems. To activate this turn the unit on let it shutdown then press the input/device and menu buttons on the front panel simultaneously and hold them in for 5 seconds after 5 seconds the power LED on the front panel will blink a two digit sequence. This will be one set of blinks a short pause then another set of blinks, this will repeat 5 times. 1 - 2 = no error detected 2 - 1 = X-ray protect (high voltage or beam current) 2 - 2 = Short protect (short protect monitors low voltage supplies) 2 - 3 = Deflection protect (this could be loss of vertical or horizontal deflection) 2 - 4 = Vertical protect (usually loss of vertical from the source) Hope this helps you!

Posted on Sep 14, 2007

  • Lashawn Robinson Sep 30, 2007

    Thank you Aleixo, happy to have helped!

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

It coming on and after a couple of seconds cut off


Without a brand AND model number or a better description of the problem, any suggestions would be nothing more than a guess.

Unless you are prepared to repair the TV yourself, professionally performed repair, even simplest ones, will probably exceed the cost of a new LCD replacement set.

Due to X-ray and other safety concerns (equipment and/or people), CRT TVs constantly check the voltages and signals required to make a CRT work. A few seconds grace is allowed during start up but after that, any excessive high voltage (real or imagined) or loss of beam deflection circuits will cause the TV to turn off.

Please do the following:
1. Move the TV to a quiet and preferable totally dark room.
Wait until night if necessary.

2. Stand within an inch or closer to the TV screen.

3. Turn on the TV and look and listen for the following:

a. Whoosh sound and/or head hair attracted toward TV screen
Yes. High voltage activated and charged CRT screen.
No. High voltage failed to activate.

b. Hissing or normal sounds from the speaker(s) while set is on.
Low voltage circuits probably okay. Defective low voltage regulator can cause high voltage to exceed limits.

c. Entire screen briefly lit up or single bright spot at center of TV screen

High voltage worked for a moment then the TV shut off due to over voltage or current problems.

d. Brief bright line from top to bottom or single bright dot on TV screen

horizontal deflection circuits bad
vertical deflection circuits ok
TV shut off due to bad deflection/sweep circuit

e. Brief bright line from left to right on TV screen

horizontal deflection circuits bad
vertical deflection circuits ok
TV shut off due to bad deflection/sweep circuit

It would be helpful for you to perform the above "up close and personal turn the TV on test" and report what happened.

Nov 26, 2014 | Televison & Video

1 Answer

My I'Art AV-32DF74 by JVC was working fine and then one day the picture and sound suddenly went off although the blue power light stayed on. There was no warning. One minute it was on and the next, it was...


first of all have u check for a bad capacitor on power supply , this capacitor is a 1000uf at 25 volts or 35 volts this capacitor controls the voltage to the secondary voltage , replace this capacitor before u do anything , sometimes it look good but is bad inside , also the other commun problem on this tv is the vertical ic if this ic if bad the tv would go in to shut donw the part # start with la45 or la78 , la76 , also u need to check for a open resistor next to the flyback this resistor work together with the vertical ic when the vertical ic gose bad it open this resistor the value 1 ohn , so 3 things u need to do first replace the capacitor if this dont work check the resistor that is close to the flybak if is open u need to replace vertical ic on this vertical u need to have 28 volts on pin 7 , this is the most commun problem on this tv , i have fix a lot of this tv with this problem before and this is what i have found ,

Jan 04, 2011 | JVC AV-32DF74 32" TV

1 Answer

WHEN I PUSH POWER BUTTON IT MAKES A LOUD POP NOISE . THEN I PRESS POWER BUTTON AGAIN SOMETIMES IT TURNS ON AND SOMETIMES IT DOESNT. ALSO THE STAND BY BUTTON FLASHES WHEN IT DOES NOT TURN ON. WHEN TV DOES...


Most likely the power supply is failing.

TVs have protection circuits to prevent full power-on if a fault is found in the high-voltage and/or high-current section of the circuitry to prevent something bad from happening, like a fire or sparks/smoke.

Oct 20, 2009 | Televison & Video

1 Answer

Rca 27410tyx1 will not shut off


Sounds like trouble in the standby/power up circuit. have you tried unplugging the TV for a half hour and seeing what happens? It might start up but I think this problem won't go away. If you heard a high pitched buzzing it sounds like a problem in the high voltage not letting the start up circuit work. threy are related. The start up circuit waits for the high voltage to stablize and then switches it on.

Sep 16, 2008 | RCA TruFlat 27F520T 27" TV

2 Answers

Sony Triniton Wega Model KV 32HS510. After pushing the power button,the tv starts to power up, then the standby light blinks 7 times then pauses before blinking 7 times again. It continues to do this,...


This is usually an indication of a failure in the scan amplifier sections. When the scan amplifiers or high voltage sections fail, the main power supply will usually also require servicing.

It is very common that the fly-back and high voltage multiplier and also the horizontal output stage fails in these sets. Along with it, the power supply will usually require to be serviced. On rare occasions, the vertical deflection amp fails.

Jerry G.

Jul 08, 2008 | Sony Grand WEGA KF50WE610 50" Rear...

1 Answer

Will not turn on


This model is equipped with a self-diagnosis feature to help with diagnosis of shutdown problems. To activate this turn the unit on let it shutdown then press the input/device and menu buttons on the front panel simultaneously and hold them in for 5 seconds after 5 seconds the power LED on the front panel will blink a two digit sequence. This will be one set of blinks a short pause then another set of blinks, this will repeat 5 times. 1 - 2 = no error detected 2 - 1 = X-ray protect (high voltage or beam current) 2 - 2 = Short protect (short protect monitors low voltage supplies) 2 - 3 = Deflection protect (this could be loss of vertical or horizontal deflection) 2 - 4 = Vertical protect (usually loss of vertical from the source.

Oct 06, 2007 | Mitsubishi VS-50607 50" Rear Projection...

1 Answer

Mitsubishi projecion tv 1995


This model is equipped with a self-diagnosis feature to help with diagnosis of shutdown problems. To activate this turn the unit on let it shutdown then press the input and menu buttons on the front panel simultaneously and hold them in for 5 seconds after 5 seconds the power LED on the front panel will blink a two digit sequence. This will be one set of blinks a short pause then another set of blinks, this will repeat 5 times. 1 - 2 = no error detected 2 - 1 = X-ray protect (high voltage or beam current) 2 - 2 = Short protect (short protect monitors low voltage supplies) 2 - 3 = Deflection protect (this could be loss of vertical or horizontal deflection) 2 - 4 = Vertical protect (usually loss of vertical from the source) 1. Self-diagnosis error 2-3 indicating deflection failure. Check for shorted or leaky Q5A37 part # 260P818050 located on PCB-Main. If found defective replace only the transistor instead of the Main PCB.

Sep 16, 2007 | Mitsubishi WS-65615 65" TV

1 Answer

No picture or sound


This model is equipped with a self-diagnosis feature to help with diagnosis of shutdown problems, to activate this turn the unit on let it shutdown then press the input and menu buttons on the front panel simultaneously and hold them in for 5 seconds after 5 seconds the power LED on the front panel will blink a two digit sequence. This will be one set of blinks a short pause then another set of blinks, this will repeat 5 times. 1 - 2 = no error detected 2 - 1 = X-ray protect (high voltage or beam current) 2 - 2 = Short protect (short protect monitors low voltage supplies) 2 - 3 = Deflection protect (this could be loss of vertical or horizontal deflection) 2 - 4 = Vertical protect (usually loss of vertical from the source)

Sep 08, 2007 | Mitsubishi VS-50605 50" Rear Projection...

2 Answers

Mitsubishi WS-55819 power issue


This model is equipped with a self-diagnosis feature to help with diagnosis of shutdown problems. To activate this turn the unit on let it shutdown then press the input and menu buttons on the front panel simultaneously and hold them in for 5 seconds after 5 seconds the power LED on the front panel will blink a two digit sequence. This will be one set of blinks a short pause then another set of blinks, this will repeat 5 times. 1 - 2 = no error detected 2 - 1 = X-ray protect (high voltage or beam current) 2 - 2 = Short protect (short protect monitors low voltage supplies) 2 - 3 = Deflection protect (this could be loss of vertical or horizontal deflection) 2 - 4 = Vertical protect (usually loss of vertical from the source) 1. SHUTDOWN AT POWER WITH SELF DIAGNOSIS ERROR 2 2. CHECK FOR LEAKY C9A60 470 PF 1000 V PART # 154P400030, PARALLEL TO D9A57 ON THE POWER PCB (NOT SHOWN IN THE SCHEMATIC). 2. SHUTDOWN AT POWER WITH SELF DIAGNOSIS ERROR 2 2. CHECK FOR OPEN FUSES F9A04 AND F9A05 PART # 283P043090 ON THE +24 AND -24 VOLT LINES. IF THE FUSES ARE OPEN THE CONVERGENCE OUTPUT CIRCUIT WOULD BE SUSPECT. 3. SELF-DIAGNOSIS INDICATES SHORT PROTECT. CHECK FOR A SHORTED IC4B01 PART # 270P261020 (VERTICAL OUTPUT) LOADING 24-VOLT SUPPLY LINE. LOCATED ON THE MAIN PCB

Aug 12, 2007 | Mitsubishi WS-55819 55" Rear Projection...

1 Answer

Static or popping sound


This model is equipped with a self-diagnosis feature to help with diagnosis of shutdown problems, to activate this turn the unit on let it shutdown then press the input and menu buttons on the front panel simultaneously and hold them in for 5 seconds after 5 seconds the power LED on the front panel will blink a two digit sequence. This will be one set of blinks a short pause then another set of blinks, this will repeat 5 times. 1 - 2 = no error detected 2 - 1 = X-ray protect (high voltage or beam current) 2 - 2 = Short protect (short protect monitors low voltage supplies) 2 - 3 = Deflection protect (this could be loss of vertical or horizontal deflection) 2 - 4 = Vertical protect (usually loss of vertical from the source.

Jul 24, 2007 | Mitsubishi VS-45605 50" Rear Projection...

Not finding what you are looking for?
Mitsubishi VS-45607 45" Rear Projection Television Logo

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1229 Answers

The Knight
The Knight

Level 3 Expert

75756 Answers

Jaime Hernandez

Level 3 Expert

2336 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...