Want to remove microwave to install new one.

Remove a GE Spacemaker
The GE Spacemaker series of microwave ovens are designed to be installed above an oven range, freeing up counter space in your kitchen. Some of these Spacemaker models are connected to an outside venting system to carry kitchen vapor and odors outside. Other Spacemaker models utilize a ductless system to do this. Removing a GE Spacemaker microwave oven isn't a difficult task, but, because of the size of some of the oven models, it is a two-man operation. Have a question? Get an answer from an appliance repair specialist now!

Other People Are Reading

• How to Remove a GE Over the Range Microwave
• How to Uninstall a GE Spacemaker Microwave

Things You'll Need

• Assistant
• Sharp knife

• Phillips screwdriver

Instructions

1. • 1 Open the cabinet above where the Spacemaker microwave oven is installed. If you see a vent in the cabinet leading to the Spacemaker oven below, your Spacemaker is vented. This vent needs to be disconnected before continuing with removal. Disconnect the vent either by loosening the duct clamps or by cutting the duct tape away with a sharp knife. Pull the vent out of the top of the oven.
     
   • 2 Have an assistant support the oven from below. Loosen the mounting screws connected to the Spacemaker through the cabinet bottom. Loosen the screws by turning counterclockwise with the Phillips screwdriver.
     
   • 3 Unplug the Spacemaker from the socket in the cabinet.
     
   • 4 Continue loosening the screws while your assistant holds the oven in place. Once the screws are removed, have your assistant slowly lower the Spacemaker down by lowering the front face at a 45-degree angle.
     
   • 5 Feed the power cable for the Spacemaker through the hole in the bottom in the supporting cabinet.
     
   • 6 Help your assistant slowly pull the Spacemaker forward and out of the mounting brackets on the rear wall. Once the Spacemaker is cleared of the mounting cabinet and rear wall, set it down.
     
   • 7 Remove the mounting bracket from the rear wall by loosening the screws.
     

Read more : http://www.ehow.com/how_7344250_remove-ge-spacemaker.html

It's impossible to say without knowing the old model number and the new model number.

But since you posted under GE, I'll assume that's your brand.

You can download GE owner's manuals and installation instructions here.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

You have a busted MAGNETRON and it's usually cheaper to buy a new oven...

When certain buttons function yet others do not the fix is to replace the touchpad

Most major manufacturers supply manuals online so if you were to log on to the manufacturer's web site, you may be pleasantly surprised as usually, if available, one is able to download, by model number, Customer Instruction Manuals, Dealer Network for spare part supplies as required.

The information is normally free of charge.

I hope this helps.

You can also download GE owner's manuals and installation instructions here.

You can find handy exploded views and order parts by model number here.

If you need simple do it yourself repair tips or a free estimate, let us know.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

It's held in place by 4 screws on the top of the microwave.

You can download GE owner's manuals and installation instructions here.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

i always reccomend to my custs that they stay with the same brand for same mounting bracket, dontreally know a way to verify other hten removing hte old micr first and then before purchasing ask to open box to check

I had same problem last week. My GE JVM1650 Spacemaker stopped after a few seconds of heating. Owned 16 months, manufactured Jan 2005. It was the magnetron, which was replaced yesterday. The magnetron has a 10-year warranty, but I had to pay $161.00 for labor by a GE technician. The call-out fee was waived at my request. I don't know what that amount would have been, but I can't believe the $161.00 for what was about 1/2 hour labor once diagnosed. Good Luck!