Question about Computers & Internet

1 Answer

Printer has good power connection but no response at all. i know power connection ok because page number light glows on printer

Power connection ok but printer lexmark 2600 series wont function at all, the only sign of life being page numbers light on, this is how i know power connection must be ok

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 700 Answers

Install its driver. Or in printing que set the lexmark 2600 as the printer to be use. Then test print. Check its data cable.

If this doesn't help leave a comment so we can device another solution

Posted on Apr 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix a Canon pixma ip6600D printer?


ALARM LIGHT which always glows - RAM error (logic board is dead)

Apr 02, 2015 | Canon Pixma iP6600D InkJet Photo Printer

1 Answer

PIXMA MG5350 WILL NOT POWER UP. HAVE CHECKED THE PLUG FUSE.


Unfortunately, I believe the printer will need to be replaced.
If you have verified the power outlet is good, there are not many options. No reset for 'No power'.

Nov 30, 2013 | Office Equipment & Supplies

1 Answer

My Kodak ESP-3 printer is not printing. There is a red light flashing and I do not know what it means. it is under the on off button. It just shoots out blank paper Kathleen


Clean the printhead, then print a test page.
  1. On the control panel, press and hold Cancel + Copy/Resume simultaneously until the On/Off light flashes. The On/Off light continues to flash during the cleaning procedure.
  2. When the On/Off light glows steady, press and hold Quantity + Cancel simultaneously until the On/Off light flashes, then wait for the test page to print.
  3. Review the printed test page and verify that:
    • the left color blocks are gray, cyan, and black.
    • the right color blocks are magenta, yellow, and black.
    • each block is completely filled with color.
  4. Is it still printing blank?
  5. Please :Call Kodak to Report Code BP03
United States Telephone Support spacer.gif spacer.gif All-in-One Printer Phone Support

Live phone support is available in English and Spanish at 1-800-421-6699, 9 A.M. to midnight Eastern time, 7 days a week.
The expected wait time for phone support is 15 minutes


  1. If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Happy Holidays!

    Thanks, Joe


Dec 22, 2010 | Kodak ESP 3 Multifunction Printer/ Copier/...

1 Answer

I just replaced both ink cartridges in my esp3 printer. But when I print, the page comes out blank


You need a new Print Head:
Clean the printhead, then print a test page.
  1. On the control panel, press and hold Cancel + Copy/Resume simultaneously until the On/Off light flashes. The On/Off light continues to flash during the cleaning procedure.
  2. When the On/Off light glows steady, press and hold Quantity + Cancel simultaneously until the On/Off light flashes, then wait for the test page to print.
  3. Review the printed test page and verify that:
    • the left color blocks are gray, cyan, and black.
    • the right color blocks are magenta, yellow, and black.
    • each block is completely filled with color.
    • Is the test page blank?
  4. 1-800-421-6699,Call Kodak to Report Code BP03

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response.

Thanks, Joe

Nov 23, 2010 | Kodak ESP 3 Multifunction Printer/ Copier/...

1 Answer

Other radio users r not able to hear me when i speak.


Could be your mic does not work. Usually CBs has paging capability, set its paging system on(check speaker set up). If your mic is OK, I suspect you don't have transmission at all. To check without having special instruments, have a PL259 connector and connect a few inches of RG8 or RG58 and connect a 12V lamp(cars signal light bulb can do) at the other end, then press your PTT button and bulb must glow and go brighter when you talk. If not glowing at all maybe your final amp is busted, have it checked by the expert. Good Luck

Mar 17, 2010 | Galaxy Radios DX-959 40-Channels Base CB...

1 Answer

Printer wont go online - light continually flashing green to yellow...


  • Unplug the printer cable from the computer.
  • Unistall the printer drivers from Device manager and also unistall the all the printer appications
  • restart the computer
  • try to download drivers from the website
  • after installing drivers and software it will ask you to connect the printer.
  • then you can connect the printer and and try to Print the test page.
Hope this help. Please Rate My Response! Thanks!
PREM

May 24, 2009 | Office Equipment & Supplies

1 Answer

Can't get printer to connect


 
Hi there,
  • Unplug the printer cable from the computer.
  • Unistall the printer drivers from Device manager and also unistall the all the printer appications
  • restart the computer
  • try to download drivers from the website by Clicking on the below link
http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&fcategoryid=116&modelid=15402#DownloadDetailAct
  • after installing drivers and software it will ask you to connect the printer.
  • then you can connect the printer and and try to Print the test page.
Hope this help. Please Rate My Response! Thanks! 
PREM  

Mar 21, 2009 | Canon PIXMA MP210 Photo All-In-One Printer

1 Answer

New Seagate FreeAgentPro USB eSATA 500GB power on light not glows


Thank you for your reply.

I have solved the problem with local help.

Printed installation manual of Seagate 500 GB eSATA external hard drive has not properly mentioned how to use power on/off switch once connected to mains. I could get local help, who has already used the device. On/Off switch to be pressed for few seconds after mains connected, sometimes it comes automatically once power is on and USB cable pluged to the USB port of PC if power supply is ok. There is no indicator for the power supply (before device glows) after connected to the mains. I was in confusion whether power supply is ok or not.

Finally, It was found that the problem was with mains power supply and I have changed the power socket and adapter.

SP Jena

Nov 18, 2008 | Seagate FreeAgent Pro - 500GB, 7200 RPM,...

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...