Question about Ovens

2 Answers

Hobart Universal Cooking Range CSD-UC

We have the above cooking range and it has an error 10 on it, can you help with this matter?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Hobart Universal Cooking Range CSD-UC

My oven keeps getting blocked with scale,we have a water softener attached that doesnt seem to have any effect
do you have any suggestions

Posted on Feb 11, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Hobart Universal Cooking Range CSD-UC

Its a problem with the drain down of the boiler, whereabouts are you located, I could have a look at it. I'm pretty good with these ovens and have even repaired numerous PCB's that even Hobart wouldn't bother fixing. They just quote you 1,040+vat for main board - crazy.

Ian 07903128897

Posted on Jan 04, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Aeg b5741-14 oven has code f5 -what does this mean?

Here is a list of oven error codes for your model Kenmore oven.
  1. F0 indicates a Stuck key pad.
  2. F1 and F7 may mean relay is turned on.
  3. F2 indicates that the oven is over temperature in one of the following modes within either cooking or cleaning mode of operation. The control is sensing over 615 degrees with the door lock circuit in the unlock mode. Control senses oven temperature above 915 degrees with the door in the locked mode.
  4. F3 and F4 indicates an open or shorted oven sensor or sensor circuit.
  5. F5 indicates a loss of relay drive circuit.
  6. FF indicates a loss of door motor safety switch.
  7. FC indicates a door lock circuit problem.
If the display of your control is flashing "F" followed by a number or letter its a range malfunction. Press the clear/off pad. Let the range cool for 1 hour and place the range back into operation.
If the problem repeats, call for service.

Jul 16, 2011 | AEG B5741-4 Electric Single Oven

1 Answer

I'm in the middle of cooking dinner and I got a f3 e2 error and the oven do I get my dinner out? My husband is an elevator mechanic so he's handy...we turned off the breaker to quit...

That code refers to the oven temperature sensor sensing a too hot oven. I suspect what you did to quite the cleaning cycle should help once the temperature cools down the door should open. I am a little confused, did you set the oven to clean while your cooking, or did it do this on its own, or was it preset and yopu forgot it was set to clean? Your temp sensor may be going bad if it just detected a too hot oven while your cooking. If it started cleaning then it may have gotten too hot and this is the safety device to prevent it from overheating. it sounds like it is trying to self clean, its essential that you find the error code sheet, stuck in the stove or oven cabinet somewhere, also check your range settings so that it is not set to auto clean.

Jun 28, 2011 | Ovens

2 Answers

We bought a house with an old wood combustion oven everhot deluxe 204. Unfortunately all the controls details have been erased with time. So we do not know where the highs and lows stands for the knobs. We...

Hi Jacqui and Sven,

Check these guys'll have to call or write, but they should be able to answer any (and all) questions about the Everhot Deluxe 204. They even carry spare parts! Hope this helped.

May 06, 2011 | Ovens

2 Answers


Please give me details of Glem gas cooking range service centres in Kerala . My id

Nov 14, 2010 | Ovens

1 Answer

Pleace HELP!!! How do I set the clock on my Russell Hobbs RHM1712 microwave?


You can set the timer on a range slow cooker to automatically switch to a warming setting when you estimate foods will finish cooking. The programmable features allow you to leave food stewing at home while you are out of the house, freeing up your day.

Set the timer on a range slow cooker to let the kitchen appliance do all the work, and come home to a fully cooked meal.

Fill the insert of the range slow cooker with food and cover it with the lid. At least a quarter of the insert should be filled with liquid to keep the environment moist during long cooking times.

Press the "On/Off" button on the left side of the electronic control panel in the front of the appliance. This will turn on the slow cooker to the low heat "Warm" setting.

Press the "Cook Time" button on the right side of the electronic control panel to add hours to the timer which will show a total time in hours with a red digital display. Continue to press the button until the display indicates the desired cook time in one-hour increments up to 10 hours.
The cooker will automatically adjust the temperature setting based on the amount of time you programmed on the timer. Cooking times of six hours or less automatically start on "High" heat and times of seven hours or more will start on "Low" heat.
A small indicator light will come on below the word to tell you the cooking temperature.

thank and thanks for using fixya.

Aug 20, 2010 | Ovens

1 Answer

Oven will not ignite because the gas is not coming out.

not a good way to light the oven . so do ck for the loose connection . as cooking will be much easer.. if gas ck the ignitor and if elect ck the connections on range pig tail ( power cord ).. mm hope t this helps...

Jul 11, 2010 | Whirlpool 30" Self-Cleaning Freestanding...

2 Answers

Bosch oven function error e124


Can you provide a model number for your oven. Is it a single oven or double ? Wall oven or free standing range ?(conventional with cooking surface)

Unfortunately the error codes for Bosch are different depending on the model of the unit.

Thank you, I`ll look for your reply.

macmarkus :)

Jan 09, 2010 | Bosch Ovens

2 Answers

I have a whirlpool/kenmore plus range that came with our house when we purchased it. Former owners did not leave a manual for it. The numbers on it are 95779890 and serial RJ3516457. I wanted to "auto...

The E1- F5 error is a door lock error.

The control (TIMER) has likely failed in this instance - BUT...

Sometimes when you disconnect power to a range and reconnect it the electronic range control gets confused.
You should disconnect power again for 15 seconds and reconnect and see if that helps.

If it doesn't cure the E1- F5 error hold the bake button in until E0- F2 appears in the display.
This is the error for a stuck button on the keypad and is the way to clear the memory of the electronic range control.

Sometimes these work, but if the control has failed it won't make any difference.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.@#$TERGD

Feb 26, 2009 | Whirlpool 30" Self-Cleaning Freestanding...

Not finding what you are looking for?
Ovens Logo

Related Topics:

345 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ovens Experts

William Miller
William Miller

Level 3 Expert

8803 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you an Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides