Question about Hotpoint Ultima WF840 Front Load Washer / Dryer

1 Answer

F08 when it finished washing the screen give message f08 and its no function at all

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 66 Answers
Re: f08

Your heater relay is stuck check all wiring connections to and from heater

Posted on Sep 14, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

F08 error code

F08 error code: Door open when program started

May 01, 2015 | Bosch Washing Machines

2 Answers

What is F08 error means in Ariston washing Machine

You did not specify model!

F08 - Heater relay cannot be activated
  • Check wiring
  • Check pressure switch and connections
  • Tap relays as they can jam on new boards
  • Check electronic control PCB
  • Check heating element


Jun 21, 2014 | Ariston Technologies Washing Machines

1 Answer

Hotpoint ultima error message f08 what does it mean?

F08 actually means the heater relay cannot be activated.
A few reasons for this, faulty heater, broken wire, faulty pressure switch or faulty main control board (the heater relay is on the main control board).
There is no reset for this.
Unplug the appliance and take the rear cover off.
Check the wiring to the heater and thermostat,give the wires a good tug as they can break internally and look ok.
If you have a multimeter, test the heater, it should read around 25 ohms.
Take the top off the appliance, locate the pressure switch (has a thin tube on it), give it a few good taps with your screwdriver handle.
Finally, take the main control board out (bottom left when viewed from the rear) and one plug at a time, take them off, clean and tighten them, plug them back on.
If everything checks out ok, then it's likely the main control board is at fault.

Feb 13, 2012 | Hotpoint Washing Machines

1 Answer

F 08 flashing on hotpoint washing machine

i found this on a website which i have used to help solve my pown problems - the follow ups state it worked for them

I had an F08 error code. I pushed a paper clip into the hole.
I didn't hear a click. I also Cleaned all the crud off the other side of the thermostats and hey presto its cleared the error and the dryer appears to be working fine

Jan 25, 2012 | Washing Machines

1 Answer

Indesit WIE127 is blinking

it needs resseting have you got the hand book as it will tell you how to if not let me know and i will look though mine and tell you how

Dec 07, 2011 | Indesit Washing Machines

1 Answer

My washing machine has just finished a cycle and an error message has appeared F-08 , cannot get machine to start

If it's Hotpoint or Creda,
F08: Heater control or NTC (Thermistor) temperature sensor problem.

Jan 24, 2010 | Washing Machines

1 Answer

Fagor Integrated Washing Machine FWM714IT error message F08 how can this be reset?

After inspecting and cleaning the pump filter, unplug unit for 20 minutes

Nov 07, 2009 | Washing Machines

1 Answer

My hotpoint ultima keeps triping the trip switch. it had f08 on the screen but now that has gone, but still trips electrics every time i press start.


f08 means heater relay cannot be actived so try unplugging heater element and see if it stops tripping the electrics.


Mar 14, 2009 | Hotpoint Ultima WF860 Front Load Washer

Not finding what you are looking for?
Hotpoint Ultima WF840 Front Load Washer / Dryer Logo

Related Topics:

1,117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts


Level 1 Expert

5 Answers


Level 1 Expert

47 Answers


Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides