Question about Kenwood VR-2080

Open Question

HOW TO WIRE MY KENWOOD SURROUND SOUND RECIEVER TO

HOW TO WIRE MY KENWOOD VR-208 SURROUND SOUND RECIEVER, TO MY SONY KDL-52V4100 T.V

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: Kenwood VR 209 Reciever, Remote Problem

http://blog.moertel.com/articles/2007/05/25/repairing-my-kenwood-a-v-receivers-remote-control-sensor

this worked on my kenwood vr-209. 10 others fixed their kenwood as well from the posts.

Jay

Posted on Jan 18, 2009

  • 140 Answers

SOURCE: kenwood vr 357 surround system stand ny light

This means there is a problem with the system it is in the protect mode it will not come out of that mode untill repairs are made. More than likley the power amp is blown.

Posted on Nov 06, 2009

  • 128 Answers

SOURCE: how to hook up a kenwood audio-video surround

hello all you need is a good pair of RCA cables.

Use the audio output on the TV
run it to the VIDEO 1 input on the receiver


as for your DVD player vcr etc you can either run them directly to the tv as it will output whatever sound is playing to the receiver.

or

use the receiver as a video switcher and connect your components directly to it.

remember your receiver will need to be set to the input you use. ie: video 1 / dvd etc..

Hope that helps

Posted on Jan 11, 2010

  • 1 Answer

SOURCE: Can I Get a Kenwood RC-R0608 Remote to work with a Kenwood VR-206 A/V Reciever

i WILL BUY YOUR Kenwood RC-R0608 Remote
rlupton@atral.com

Posted on Jul 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a kenwood Auto video surround receiver DR / 409 how to reset it


PDF]KRF-V8030D VR-409 - Kenwood

manual.kenwood.com/files/B60-4593-00.pdf
VR-409. INSTRUCTION MANUAL. KENWOOD CORPORATION. B60-4593-00 (EN) ...on the country and sales area. AUDIO VIDEO SURROUND RECEIVER ...

Kenwood VR-409 Manuals

www.manualslib.com > Brands > Kenwood Manuals > Stereo Receiver
View online or download Kenwood VR-409 Instruction Manual. ... Kenwood Instruction Manual Audio Video Surround Receiver KRF-V8030D VR-409.

Kenwood VR-409 Receiver Repair Questions, Solutions ...

www.fixya.com > Forum > Audio & Video Receivers > Kenwood
Recent Kenwood VR-409 Receiver questions, problems & answers. Free expert DIY tips, support, troubleshooting help & repair advice for all Audio & Video ...

Kenwood VR-409 PDF Owner's Manual Download & Preview

www.manualguru.com > Kenwood Manuals > VR-409

Feb 03, 2016 | Kenwood Audio Players & Recorders

1 Answer

Kenwood vr606 reciever shutting off subwoofer and centre speaker simultaneously after few minutes/seconds of powering on. WHat's the cause?


The receiver's out put sections are grouped in pairs. Front left and right in one output, rear left and right in second output, and center channel and sub output on the third. Sounds like a semiconductor or semiconductors have gone bad in the center & sub output.

Nov 19, 2015 | Kenwood VR-606 Receiver

1 Answer

Problem with sound on sony KDL-52V4100


I think you have a circuit issue not a software issue.

May 02, 2017 | Sony Bravia V-Series KDL-52V4100 LCD TV

1 Answer

Kenwood Receiver VR 806 turning off


Sounds like the music amplifier is different to the tuner audio amp. The music amplifier is now looking at an unbalanced impedance which is less than it should be. Therefore the output chip of the music amp has more current through it than it wants so it gets hot and shuts down.Put a four ohm wirewound resistor ( from Radio Shack ) in series with each surround speaker to reduce the current flow through the amplifier output.

Apr 09, 2010 | Kenwood VR-806 Receiver

1 Answer

No surround sound from Kenwood VR-5090


please select the 5.1 option in the audio menu of the reciever.

Jan 10, 2010 | Kenwood VR-5090 5.1 Channels Receiver

1 Answer

I have a kenwood vr-707 it gets surround sound on dvd/vcr but I can't get surround sound on just tv.


Well you have a built in decoder/surround processor that will detect a signal with the surround sound info(dvd/sat.receiver/cable converter etc.) and will then process it to the different speakers on your system. In the absence of that signal it will process it as standard stereo sound(two front speakers). You may want to look in your receiver functions/menu for simulated surround.
Hope this will help.

Nov 24, 2009 | Kenwood VR-707 Receiver

1 Answer

No sound from surround speakers


you have it set in stereo mode change listen sound to auto this way whatever way the signal is coming thru you will hear it

Jan 09, 2009 | Kenwood VR-405 Receiver

Not finding what you are looking for?
Kenwood VR-2080 Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5017 Answers

Eddie Dalton
Eddie Dalton

Level 2 Expert

53 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a Kenwood Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...