Question about Washing Machines

1 Answer

Maytag epic front loader

Not sure, but washer does not seem to be using enough water... When we first installed it, we ran it through with no clothes and the water came up about 3 inches on the door.... On our first load of clothes, the washer was adding water constantly, as the cycle was nearing end, we got an f09 error..... After a few more tries we would get an fh error.... now we get no error messages but the washer does not seem to add enough water to wash or rinse the clothes.... we have resorted to adding water, but this takes to much time and energy, considering we paid close to 900 for this machine.... any ideas? have others experienced this problem, find it hard to believe that the washer is working properly.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,294 Answers

Suggestion: Check the wall inlet to see if water comes freely; then check if the inlet valves behind your machine to see they are not clogged. Best that u open the valve full before you begin your wash. The water coming 3 inches/door is normal. Dont try opening the door until after you hear a click or aft 2 or three minutes aft wash cycle completes.

Posted on Sep 12, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My epic front loader is make a very very load noise when in the spin cycle. Not quite at all.


OH,OH!!!, I think the main bearing is bad on the washer, see if the inner tub has play by moving it up and down. even if is not I'm sure the bearing is bad. with time and clothing weight the water seal worn allowing water to wash the lubrication in the bearing. this is a mayor repair.

Feb 09, 2011 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

Maytag the washer quits and a f20 or f11 shows up


Its a water inlet problem (no water or insufficient water supply) check your washer inlets, maybe the water valves are off or you don't have enough water pressure.

Apr 01, 2010 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

I have front loader MFW9700 Maytag washer. Water


Check the door seal for tears and the drain boot from tub to drain boot for anything that might have put a hole in like a piece of metal from an under wire bra which front loads will spin so fast that the wires come out of the bras.

Feb 01, 2010 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

Setting question


when my front loader was giving me the f-01 there were three diffrent times one was water pressure 2 was soap wat to suddy 3 not enough power which is the most common another was off balance and load to heavy funny they all have the same err code #

Dec 24, 2009 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

I need to change the bellow on my maytag front loader. Do you have any instructions?


The following link explains how to change the bellow on a Maytag Epic:

http://www.fixya.com/support/r385211-replacing_door_bellow_whirlpool_duet

Later models of Maytag washers are manufactured by Whirlpool, so these instructions should apply. If you have any questions, please let me know. I hope this helps you.

Sep 02, 2009 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

Front loading Maytag Neptune doesnt drain all water


Remove the pump and clean it out. Access the pump from the rear.

May 25, 2009 | Maytag Washing Machines

1 Answer

Front loading Maytag Neptune doesnt drain all water


the washer has a low level of water in it at all times. it will never completely drain out unless you pump it. this is one of the reasons there is such a smell with these washers, i use vinegar in rinse cycle and i use bleach once sometimes twice a month to keep mold and mildew smell away.

Mar 08, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag front loader washing machine


sounds a s if you have ablockage within oyour pump assy, remove th elower acess panel and undo the "button trap" your problaby clogged up

Jan 24, 2009 | Maytag EPIC MFW9700S Front Load Washer

3 Answers

Maytag epic


hi there,

the FH error means it's either you have a drain problem if there is water in it or if if there is now water in it, make sure that both water inlets are turned all the way up. check to make sure that you don't have any water leaks anywhere visible.

Oct 03, 2008 | Maytag EPIC MFW9700S Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

78289 Answers

Brad Brown

Level 3 Expert

16994 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...