MY NETGEAR SPH 200D IP PHONE NOT CNNECTIONG TO INTERNET . I GET MESSAGE SYSTEM STARTING UP BUT NEVER WORKS. I DONOT HAVE INSTALLATION CD

I think to no need to installation CD for netgear wireless router, just reset your router, press on reset button and other think in the bottom of router given your router IP. Type your IP in browser URL then set your all settings. If not solve your problem you can try on netgear support.

Netgear Router Support Phone Number 1 800 335 8177 Netgear Support

Lets remove the netgear router from the equation. Plug your desktop directly into your modem (comcast, verizon, embark, etc). Let the computer grab an IP and test your internet.

If you are able to surf the internet then the problem resides on the PCI Card. Try downloading the new drivers online.

You can use below steps to install router

ROUTER SETUP

1. Please remove all the connections from the router. Connect power to the router and then connect a cable from the computer into any of the 4 lan ports on the router. Make sure the modem should not be connected to the router or to the computer.
2. Open up the Internet Browser (Safari, Internet Explorer, Mozilla Firefox, Opera, etc.).
3. Put http://www.routerlogin.com/basicsetting.htm or 192.168.1.1 address bar. press enter
4. Login to the router with the Username as "admin" and Password as "password" (please note that the Username and Password are case sensitive).
5. Click on lan ip setup under advanced.
6. Change the lan ip to 192.168.10.1 and under use router as a dhcp server change the starting ip as 192.168.10.2 and ending ip as 192.168.10.51, click apply and click ok for any popup message that arise.
7. Once the browser display some error message like CANNOT FIND SERVER, ACTION CANCELLED etc, Connect the dsl modem on the wan port of the router and restart the computer.
8. Power off the dsl modem and the router after making the connections.
9. Power on the dsl modem and wait till the dsl light comes on, then power on the router.
10. Open a web browser (Internet Explorer, Mozilla Firefox or Safari).
11. Access the router (http://192.168.10.1).
12. Login to the router (Username = admin Password = Password).
13. Click on Setup Wizard and then select "Yes" and Click "Next" on the detection window.
14. It should give you a "Dynamic IP Detected" or "pppoe detected"(type the Username & Password of your dsl account in case of pppoe detection) and then click next.
15. Click Apply.
16. Logout of the router.
17. Open up another browser window and try to access internet.

Please rate the service positively if issue resolved
Thanks for using Fixya

I suggest try to check the netgear if it is connected to the internet. If the wirelss signal is good, it might be the internet connection is having some issue.
What you can try to do first is:
1.connect a computer to the netgear directly using an ethernet cable (RJ45)
2. click start then select run type cmd (It's a black screen)
3. type ipconfig/all then press enter on your keyboard
4. check the ip address it should be 192.168.X.X and the default gateway is 192.168.0.1 or 192.168.1.1 depending on the router default ip address
5. on the black screen type ping yahoo.com then enter on the key board
*if there is a "reply from" message it means there is an internet connection going in the router and you need to configure the router. *If the message is "unable to detect" or "request timed out". You need to contact you Internet Service Provider for assistance.

Hi Nick,

This is common issue with most of the NETGEAR products. NTP server used to synchronize time seems to be working intermittently. The only thing I can suggest you to do is to upgrade the firmware on the phone.

Visit the link below to download the firmware for the phone:

http://kb.netgear.com/app/answers/detail/a_id/677

I hope this information allows you to resolve this issue.

If I have helped you, please help me, and rate this suggestion the highest FixYa rating. If you cannot rate this post with the highest rating, then please comment to this post and I will try to help you further.

Regards
Anand

Make sure your desktop doesn't have static IP address. Go to Network Connections, Properties of Local Area Connection, Internet Protocol > Properties. Select Obtain IP Address Automatically and Obtain DNS Servers Automatically. Apply the changes and restart the computer.

so you are not able to connect wifi on your acer so please follow the steps to trace the problem.

1>check your wifi is installed and active
2>check you are getting single strength good or excellent
3>check whether dhcp is enabled and give the proper range ip is defined.
e.g type in start --> run -->http://default ip of netgear rotuer and login with admin & password admin.
4>right click on my network place and goto properties -->internet protocol tcp/ip and set it for obtain ip address automatically and dns also auto
This might help you in resolving it.

you can access the router's setup page and setup your internet connection form there. follow the steps below

1. Connect a computer to any one of the four LAN ports of the NETGEAR router.
2. Open an Internet explorer and type the router IP address which would be either http://192.168.0.1 or http://192.168.1.1 (by default, refer to your product documentation ti determine the default IP address.) in the address bar and press Enter.
   The Login window will be prompting for a Username and Password. The default Username is admin and the default Password is password
3. then setup your connection according to the settings provided by your ISP

Chapter 1: Connecting the Wireless-G Broadband Router
Hardware Installation
1. Locate an optimum location for the Broadband Router. The best place for the Broadband Router is usually at
the center of your wireless network, with line of sight to all of your mobile stations.
2. Fix the direction of the antenna. Try to place it in a position that will best cover your wireless network.
Normally, the higher you place the antenna, the better the performance will be. The antenna's position
enhances the receiving sensitivity.
3. Connect a standard Ethernet network cable to the Broadband Router’s Internet port. Then, connect the other
end of the Ethernet cable to your Cable or DSL Broadband modem.
4. Connect your network PCs or Ethernet devices to one of the Broadband Router’s numbered ports with a
standard Ethernet network cable.
5. Connect the AC Power Adapter to the Broadband Router's Power Socket and the other end into an electrical
outlet. Only use the power adapter supplied with the Broadband Router. Use of a different adapter may result
in product damage.

Chapter 2: Configuring the PCs
Overview
The instructions in this chapter will help you configure each of your computers to be able to communicate with
the Router.
To do this, you need to configure your PC’s network settings to obtain an IP (or TCP/IP) address automatically, so
your PC can function as a DHCP client. Computers use IP addresses to communicate with the Router and each
other across a network, such as the Internet.
First, find out which Windows operating system your computer is running. You can find out by clicking the Start
button. Read the side panel of the Start menu to find out which operating system your PC is running.
You may need to do this for each computer you are connecting to the Router.
The next few pages tell you, step by step, how to configure your network settings based on the type of Windows
operating system you are using. Make sure that an Ethernet or wireless adapter (also known as a network
adapter) has been successfully installed in each PC you will configure.
Configuring Windows 98 and Millennium PCs
1. Click the Start button. Select Settings and click the Control Panel icon. Double-click the Network icon.
2. On the Configuration tab, select the TCP/IP line for the applicable Ethernet adapter.
Do not choose a TCP/IP entry whose name mentions DUN, PPPoE, VPN, or AOL. If the word TCP/IP appears by
itself, select that line. Click the Properties button.
3. Click the IP Address tab. Select Obtain an IP address automatically.
4. Now click the Gateway tab, and verify that the Installed Gateway field is blank. Click the OK button.
5. Click the OK button again. Windows may ask you for the original Windows installation disk or additional files.
Check for the files at c:\windows\options\cabs, or insert your Windows CD-ROM into your CD-ROM drive and
check the correct file location, e.g., D:\win98, D:\win9x, etc. (if “D” is the letter of your CD-ROM drive).
6. Windows may ask you to restart your PC. Click the Yes button. If Windows does not ask you to restart, restart
your computer anyway.
Configuring Windows 2000 PCs
1. Click the Start button. Select Settings and click the Control Panel icon. Double-click the Network and Dialup
Connections icon.
2. Select the Local Area Connection icon for the applicable Ethernet adapter (usually it is the first Local Area
Connection listed). Double-click the Local Area Connection. Click the Properties button.
3. Make sure the box next to Internet Protocol (TCP/IP) is checked. Highlight Internet Protocol (TCP/IP), and click
the Properties button.
4. Select Obtain an IP address automatically. Once the new window appears, click the OK button. Click the
OK button again to complete the PC configuration.
5. Restart your computer.
Configuring Windows XP PCs
The following instructions assume you are running Windows XP with the default interface. If you are using the
Classic interface (where the icons and menus look like previous Windows versions), please follow the
instructions for Windows 2000.
1. Click the Start button and then the Control Panel icon. Click the Network and Internet Connections icon.
Then click the Network Connections icon.
2. Select the Local Area Connection icon for the applicable Ethernet adapter (usually it is the first Local Area
Connection listed). Double-click the Local Area Connection. Click the Properties button.
3. Make sure the box next to Internet Protocol (TCP/IP) is checked. Highlight Internet Protocol (TCP/IP), and
click the Properties button.
4. Select Obtain an IP address automatically.
Once the new window appears, click the OK
button. Click the OK button again to complete the PC configuration.