Question about Panasonic BL-C30A Network Camera
Thank you for contacting Panasonic. We apologize for the delay in our response.
The CD can obtained through our parts department at 1-800-332-5368 or through the link below:
It can also be downloaded at http://netcamdealer.com/resources/file/82/103
The CD-ROM is not needed for setup. To setup the camera, type in the local IP address of the camera. If you do not know the IP address of the camera, press the reset button on the back of the camera to reset the IP address. This will default the IP address to http://192.168.XXX.253, with the XXX being replaced by the 3rd octet of your router IP address. For example, if your router IP address is 192.168.0.1, you will type
http://192.168.0.253 into your internet browser and you will be able to configure the camera. Another example is if your router IP address is 192.168.1.1, you will type http://192.168.1.253 into your internet browser and you will be able to configure the camera.
To obtain additional assistance for your product, please contact our Panasonic Customer Call Center at 800-272-7033. The hours of operation are Mon. - Fri. 9A.M to 9PM and Sat. - Sun. 10A.M to 7PM Eastern Standard Time. A representative will be available to assist you. Please have your case number 26813996 available at the time of the call.
Panasonic Consumer Support
Posted on Sep 04, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Jun 04, 2014 | Cell Phones
First download and install Pheonix from this link. Nokia Phoenix Service Software 2011 - Download secondly Download flash file from this link 3110c file and install it to C / program files/pheonix.. after finished this installation open pheonix . Inside the interface at the> top left <there you see "File" click there and choose "open file" and then select the approprait Product type i.e "which is written on the back panel inside the battery of every Nokia(Type RM-000).After doing this again at the left top count from "File"1..2..3..the 4th one is "Flashing" press there, when you click there you'll see three sub-menus, just select the "Firmware Update" again you'll see another interface. Look at the product code there should be blank and put your "mouse tool" at the straight end from the "Product Code" there is a Button and choose the code which is written in the back side of your phone. e.g CODE:0000000.if the same code does not found just take one which is higher. After this you can see "Dead phone USB flashing" click that box. Now this is the last stage... Connect your phone with the USB to your PC and let the driver install ...wait for a moment.(If your phone working).Lastly after just finished (In case your phone is Dead, unable to switch on in normal mode start from here) Connect the phone to pc without powering...insert good battery and Click the "Referbish" button after this, a message will prompt you "press power botton" etc. insert charger or press it and wait until the phone will Restart automatically in normal mode 10-15 minutes. If you cannot understand just leave a Comment / Click here1. thanks for visiting fixya. Good luck.
Sep 06, 2011 | Nokia 3110 Cellular Phone
Aug 26, 2011 | Intel CELERON 2.66Ghz CPU AND MOTHER BOARD...
Mar 08, 2010 | HP Pavilion dv6000z Notebook
Nov 02, 2009 | Panasonic BL-C30A Network Camera
Nov 01, 2009 | Panasonic BL-C30A Network Camera
Jul 05, 2009 | Motorola Mobility RAZR V3i Cellular Phone
Jun 01, 2009 | Computers & Internet
2,747 people viewed this question
Usually answered in minutes!