Question about Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

1 Answer

Quiet Series 100

Hello, My Quiet series is not quite 3 years old and besides the noise works good. However the other day i did a load and when all was said and done it did not clean anything. The water enters into the dishwasher, i can hear the motor but the water does not spray around inside the dishwasher. The motor does not seem seized as i can turn the blades for the water. Can you please suggest to me what the problem is All lights work on the door, the water goes in and if i hit cancel will drain out...but the water does not spin around inside Please help Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 641 Answers
Re: Quiet Series 100

It sound like a pump issue. The dishwasher has a motor that attached to a pump which forces the water up into the sprayer arms and during the drain cycle, it pushes the water out of the dishwasher. The motor (and pump) located beneath the dishwasher. Check if pump spins when it should force the water up into the sprayer arms. In case it doesn't spin you should replace the pump. Good luck !

Posted on Sep 11, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

3 Answers

1.5 year old Maytag Legacy Series Quiet Series 300 Lock Light on

Hold down the heated-dry button for 3 seconds and the light will clear.

Nov 07, 2009 | Maytag 24 in. MDB9750AW Dishwasher

2 Answers

Foul smell coming from Maytag Quiet Series 300

Hello jscott,
It is typical nowdays for most dishwashers not to drain all water out of the bottom tub (Even where you cant see) due to siphon design and energy efficiency. Try using about a liter of vinegar and throw it on the bottom tub of the dishwasher. Let it run through a full cycle and see how that works. Has worked for me

Sep 07, 2009 | Dishwashers

2 Answers

Maytag Quiet Series 100, Model # MDB5600AWS, built in dishwasher. Does not get the dishes clean, dishes stay dirty after multiple cycles of washing. Please help!

We also have a Quiet series 100 and had the same problem, the dishes always came out dingy or with food all over them. My washer is about 5 years old and worked well for about 4 of them but the last year has been doing a poorer and poorer job washing the dishes. I finally broke down and removed the racks and all of the plastic parts from the inside of the washer. Doing this revealed that the groves in the under side of most of the plastic parts was clogged with food and debris. After a good scrubbing with water and a brush then reassembly it worked like a new washer again, cleaning the dishes very well and the best part is it saved us about $700.00 for another washer.

Jun 20, 2009 | Whirlpool GU2400XTP Built-in Dishwasher

2 Answers

My Maytag dishwasher Quiet series 100 gets no water

I would cheak your float switch witch is located on the bottom of inner dishwasher move it up and down may be stuck.then try.If that will not work you may have a bad micro door switch.Good luck:)

Apr 08, 2009 | Maytag MDB5100A Dishwasher

2 Answers

Maytag Quiet Series 300 Legacy Series Dishwasher

Mine was doing the same thing and I just pressed and held down the heated dry button until the light went off. Then I was able to start my machine as usual. Hope this works for you.

Mar 12, 2009 | Dishwashers

2 Answers

Maytag quiet series 300

Maytag Quiet Series 300. The lights flash in sequence starting from the outside traveling inward. The timer counts backwards from 50 to 1. Then the sequence starts over. and continues over and over. I'm able to clear it when the time reaches 1 or 2. It stays off for a while (3-4 hours) then starts over. I can not clear the countdown until it reaches 1 or 2. After I clear it the dishwasher will work, but until then, no way. This happens with the door open or closed.

Sep 15, 2008 | KitchenAid 24 in. KUDI02IRBS Stainless...

2 Answers

Kenmore Dishwasher displays the number "98"

I have a very similar problem. When I push a wash selection, every light on the panel shows up...and when I push Start, nothing happens. When I push cancel, it trys to drain, even tho no water is in there any more. Have you ever had an answer to your problem?

Feb 06, 2008 | Kenmore 16872 Built-in Dishwasher

1 Answer

Maytag legacy series 3 yr's old

I had a similar problem where slowly specific buttons stop working. Moisture was getting into the control board and slowly killing buttons. I replaced the control board and that worked for another year, until the buttons began dying again.

For now, there are other ways to start the machine, but you just have to let time expire to stop it. It is probably a control board issue.

Dec 12, 2007 | Maytag MDB7100AWB Dishwasher

1 Answer

My Energy Star/Built-in

Me to....My dishwasher is about 7 months old. It use to be extremely quiet. Now it is LOUD. but still works fine. HELP!

Oct 18, 2007 | KitchenAid 24 in. KUDI01ILBS Stainless...

Not finding what you are looking for?
Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher Logo

451 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Maytag Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides