Question about Gaggia Titanium Espresso Machine

2 Answers

Frosen my display is frosen, on rinsing cycle. and fill watertank, and i have tried. to shut off the machine but nothing happens. ?s there a reset button? please help.

Posted by on

  • badwolf78731 Jan 31, 2008

    My Titanium keeps going into rinse cycle by itself and when it does, the buttons are frozen. Eventually after running something like 4 full tanks of water through the machine it goes back to normal. I had guessed the motherboard is fried but after sending off to be repaired, the tech could not get the problem to happen. Soon as I get it back (3 months without my machine and having to use a drip coffee maker! but that is another story) my Titanium immediately goes into rinse mode. I called a different repair place and the tech there thinks the mother board is bad. I do not want to be with out my machine for another 3 months. Any advice?

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

The duration of the rinsing cycle is equal to the amount of water you have in the water tank. I don't believe they tell you this anywhere in the manual! I own a Titanium SS and it rinsed and rinsed and rinsed the first time I performed it! I figured out it will just keep going until the water tank sensor tells the machine it is out of water which is equal to saying to it: "Thanks for using all the water i wanted you to use to rinse, now you're finished." It takes a LONG time if you fill the tank. If you keep filling the tank, it will just KEEP going. Be patient, let the tank run out of water and this will trigger the end of teh cycle. Hope this helps, Tony.

Posted on Jan 04, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Wops. Sounds like the motherboard on the machine is broken. Had the same problem with my machine and had to replace.

Posted on Dec 16, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you descale


usually with a white vinegar cycle

Mar 30, 2015 | Saeco Magic Comfort Plus Espresso Machine

1 Answer

The cleaning cycle wont work.


Did you tried with different load?
It could be the control panel which is not to cheap.

Mar 09, 2013 | Whirlpool GHW9150 Front Load Washer

1 Answer

Our Comfort machine won't brew and constantly displays, "Fill Watertank" even with the tank full. In order to brew, one has to remove the water tank then gently lower it only partially down in place. As...


Hi
The magnet in the water tanks is either upside down or has sunk to the bottom of the tank. It should float to the top of the cage it is in and it should have a flat top not rounded. If its rounded side up the magnet is upside down. This is what would cause your problem.

Sep 22, 2010 | Saeco Magic Comfort Plus Espresso Machine

1 Answer

The S9 has been unused for three months and I cannot get it to get water to the brewer. It keeps telling me to fill the water and press the steam button. No such luck. Is there a way to prime this machine?


Hello
This is a common problem and there`s usually only 1 thing you can try to do yourself. Use luke warm water in the watertank and repeat the fill system procedure 4-5 times. If this doesn`t help, try to shut down the machine and try the same after 30 minutes. If nothing happens after you tried this a few times, then theres a problem with the solenoid valve for steam, and this need to be changed. That`s something you need help from a technician for.

Jun 13, 2010 | Jura Capresso Impressa S9 Coffee...

1 Answer

Exactly the same problem - fill watertank message


clean unit with vinegar and water. run two or three cycles then flush with two or three cycles of straight water

Jun 13, 2009 | Saeco Incanto Classic Espresso Machine

2 Answers

Cold water will not stop filling during rinse


while the unit is filling in the warm cycle. reach behind and shut off the hot water tap.I bet the water flow stops filling, if so, you would need to change the inlet valve on the machine. You see, in warm, if the cold is not filling, you still hear the hot filling and the unit will advance. The rinse cycles are mostly "cold" only. if the valve is not opening it will not allow it to advance from the rinse section on the board.

Good luck!

Feb 16, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Machine says malfunction and won't froth milk


If you have a rotarywheel; Press and hold to enter the menu, turn to Maintenance, select Decalcify unit; empty tray as requested, fill up 600ml water in a container. Disolve 3 Descaling tablets in the water, and then fill it in the watertank. Press Maintenance button and you`re off.

If you don`t have a Rotary; Turn off the machine and let it cool down for a while, then push the Rinse/Maintenance button for a few seconds; then you will get the message Empty tray. Fill the solution in the watertank and press button.

It`s important that you use the right amount of water, or else the process will "never" finish.

Dec 24, 2008 | Jura Capresso Impressa S9 Coffee...

1 Answer

Rinsing cycle won't START


After all, I turned machine off with power switch, waited 30 seconds and turned it back on. It displayed "RINSING CYCLE" message, but this time went through regular rinsing cycle, then rinsed thoroughly (I counted several cups of water) and RETURNED TO NORMAL.

Halleluiah! Now I can get my morning coffee again!

Aug 30, 2008 | Gaggia Titanium Espresso Machine

1 Answer

Shutting down on rinse cycle


Hi this could means that you may need to replace the washing machine bearings. Once the bearings are bad, the motor overheats and it will automatically shut down after the first rinse.

Timonty from WashingMachineAdvisor.com

Jul 28, 2008 | Kenmore 44072 Front Load Washer

1 Answer

Display says system will be filled with water but nothing happens


I solved the problem. The hot water escape was blockt by a piece of lime. So the pressure was to strong to let water in the system. You have to dick with a little needle in the small hole of the escape. That´s it.

Feb 17, 2008 | Krups Orchestro Dialog FNF2 Espresso...

Not finding what you are looking for?

Open Questions:

See all Gaggia Titanium Espresso Machine Questions

Gaggia Titanium Espresso Machine Logo

457 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gaggia Coffee Makers & Espresso Machines Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Oloyede Monsuru

Level 3 Expert

1417 Answers

Michael Vincent Cruz

Level 3 Expert

868 Answers

Are you a Gaggia Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...