Question about Computers & Internet

1 Answer

Burner disconnected - Computers & Internet

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 432 Answers

Take the side off and make sure that the data cable and power connectors are seated firmly and also if this is an IDE drive check the jumpers.

Posted on Apr 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the front of a ftat top range


see this guide and fix it. God bless you
Instructions
    • 1 Disconnect the power to the stove by turning off the breaker in your fuse box. Test the stove to ensure that power has been disconnected by turning on a working burner and making sure it does not get hot.
    • 2 Open the oven door.


    • 3 Remove the two bolts from the underside of the front of the cooktop, located just above the door jam, facing upwards.
    • 4 Lift the entire cooktop to access the burners, which are attached to the bottom of the cooktop.
    • 5 Remove the two screws from the brackets that secure the burner that you would like to remove, then remove that burner.
    • 6 Disconnect the wires connected to the original burner, then plug them into the new burner. The wires can be removed by simply pulling them out of the terminals. Be sure to mark which wires go to which terminal.
    • 7 Align the grooves on the top of the new burner with the grooves on the bottom of the glass cooktop, then secure the new burner using the brackets and screws that you originally removed.
    • 8 Lower the cooktop, then re-secure it with the two bolts that were removed from the bottom. Close the oven door.
    • 9 Restore power to the stove to complete the installation.

Oct 02, 2012 | Frigidaire Kitchen Ranges

1 Answer

On a kenmore 5 burner grill when lighting the fourth burner all of the grill shuts down, regardless of which is the fourth burner?


Sounds like the pressure regulator is malfunctioning. Try disconnecting your gas line. Open/Close all burners then reconnecting gas. If propane, don't turn bottle off before burners. Always turn burners off first, then bottle. then bottle on before burners. This primes the regulator to the proper pressure.

Jan 09, 2012 | Kenmore Grilling

1 Answer

My Weber genesis silver is working but the flame is very weak. Is there a way to clear the burners?


Occasionally you can clear air from the burners by turning the burners on (with gas shut off) and disconnect the propane tank. Once the tank is disconnected, turn the burners off and reconnect the tank. This should dispel any air. You can also take a wire brush and "gently" brush the burners. Occasionally a little debris will clog the burner. Since this seems to be happening on all of your burners, it's a good bet it's air causing the problem.

Oct 09, 2011 | Weber Genesis Silver B Grill

1 Answer

Ancient (1971) Frigidaire Cookmaster electric Compact 30 Range/Oven, model number RBG-533N, has two surface mounted red indicator lamps; one for the oven & one for the burners. The surface burner...


The stove has 4 burner switches with a # 2 terminal on each switch. This contact is similiar on all four switches. One of the switches # 2 contact is stuck. The burner switch should disconnect both legs of the 240 volt circuit, one leg through the # 2 terminal and one leg through the thermostat built into the burner switch. Disconnect the pilot lamp wire on each switch unti the light goes off and then replace that burner switch. This should correct the problem

phucks001@horrycountyschools.net

Oct 08, 2010 | Frigidaire Kitchen Ranges

1 Answer

Heating elements on stove top stopping heating


To test the heating element, do the following steps:
First, disconnect the heating element from the stovetop. In most cases, this is done by lifting up the burner on the side opposite of the terminals (the part of the burner that disappears under the stovetop). Remove the decorative ring.

Inspect the style of connection. If the burner element has visible blades that fit into the receptacle block, pinch the block with one hand, and pull the heating element free with your other hand. If the terminal block clamps over the element, the housing must be removed and the burner wires disconnected. Unsnap the metal piece or remove the screw that secures the receptacle block and then disconnect the element.

Inspect the heating element. If you find bubbles, warping, or damage to the insulation sheath, the burner must be replaced. If the terminals are dirty or corroded, this can cause poor temperature control, intermittent problems or complete failure to heat. Clean the terminals with steel wool or very fine sand paper to restore good conductivity.



Jan 19, 2010 | Electrolux Kitchen Ranges

1 Answer

System won't allow me to delete below entry HKEY_LOCAL_MACHINESYSTEMCurrentControlSetControlClass{4D36E965-E325-11CE-BFC1-08002BE10318 in order to get pioneer dvd drive going again what do I do now thanks


Disconnect the drive from the PC or disable it through BIOS, then boot, remove the entry and, if you disabled the drive reboot the PC and enable it through BIOS, if you disconnected it then turn off PC, reconnect it and Boot.

Nov 18, 2009 | Pioneer DVD Burners DVR-K13 Burner

1 Answer

I have a 5 burner Dacor Cooktop (SGM365) with which I am having trouble with the right rear burner not sparking. There is gas flow and the other burners are lighting just fine. I've taken the burner apart...


In the middle of each burner, there is a small brass ring that screws in the burner. If you unscrew all five and pull the knobs, the top should come off. From there you can access the electronics. Because all the burners ignite at the same time, I would suspect either a disconnected or shorted wire on your right burner or some corrosion has occurred at that burner preventing it from grounding properly.

Nov 09, 2009 | Dacor Preference SGM365 Gas Cooktop

1 Answer

All 4 ignators are spaking with the contrtols on off position on my GE JGP328 cook top


It's the Switch Harness. Do not remove the stove and disconnect it from the gas. Turn the gas off under the stove. Take off the: knobs and the plate; burners; hxw screws. Pull burners out and disconnect igniter burners. Lift the top of the oven off. The Switch Harness is on the right, under where the knobs are located. Replace the Switch Harnes.

Mar 30, 2009 | GE 30 in. JGP328 Gas Cooktop

1 Answer

GE Elec Range - front left burner will not turn on


If you have the glass cooktop slide-in model, the problem is most likely the burner "ribbon' under the glass top for the small burner has come loose. I fixed mine with only a phillips-head screwdriver, needle-nosed pliers, and a 1/4" wrench (1/4" socket on the end of a nutdriver works better). Here are the steps I took to fix it: 1) Slide the oven out from the counter so the sides of the oven are clear of the counter top. 2) Remove the phillips head screws-1 on each side of the oven near the top/rear. These will be the only phillips-head screws you will need to remove. 3) Open the oven door and remove the 4 hex-head screws at the top/front/inside the oven- there are 2 on each side which follow the opening of the door. Then close the door. 4) Pull off the burner knobs by gripping them and pulling straight up. Don't worry, you will not break them but you will need to give them a good tug. 5) Remove the burner retaining nuts that are under the knobs-you may need a wrench to loosen them but only tighten them by hand when reinstalling. 6) Pull the face of the control panel away from the oven slowly until you see a ribbon connector on the right side and then disconnect the ribbon and remove the face plate from the oven. 7) Remove the 4 hex-head screws from the face plate bracket (the plastic part that was holding the face plate) and pull the bracket toward the front of the oven until it flops over and rests on the oven door handle. 8) remove the 2 black screws holding down the glass top-one on each side of the oven-the screw heads face the front of the oven. 9) Disconnect the two wiring harnesses attached to the cook top. Don't worry, they only fit one way so you don't need to label them. 10) Lift the cook top until the wiring harnesses are clear of the holes and place it upside down on a flat surrface. 11) Remove the two retaining bracket screws and brackets from each side of the non-working burner. 12) Slowly lift the burner and flip it upwards until you see the ribbon coils. It should not be necessary to disconnect any wires. 13) Look at the ribbon coils very carefully to see if any of them are disconnected from their main connection points. If so, feed the ribbon back inside the pinch point (you may need a small screwdriver to open the pinch point first) and then use a pair of needle-nosed pliers to pinch the ribbon to hold it in place. I had to use a voltage meter set in the OHM position to find where mine were disconnected. Once you pinch the ribbon end back into place, put everything back together in reverse order. If your burner still does not work, your burner knob switch may be bad. I hope this helps. Good Luck!

Dec 26, 2008 | GE Profile JB968SHSS Electric Kitchen...

2 Answers

C d burner


Well first try using it with a different system and see if it works.Also check in the device manager if it is recognised over there.You could also try to reinstall the software for it.

Dec 26, 2007 | Computers & Internet

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...