Question about Husqvarna Lawn Tractor 48" Deck, 23 Hp, Model# Yth2348

1 Answer

Husqvarna yth2443t little or no movement

Very little or no movement, forward or reverse, no belt squeal or smell, no other sounds of trouble,

Posted by on

  • rgoslo Apr 16, 2009

    mine started only forward and only sometime. now both forward and in reverse. all the time

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Make sure the trans. linkage can operate freely. Had the same problem,it was just a build up of grass and dirt.

Posted on Apr 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My husqvarna yta 18542 will go forward but not reverse


Linkage to the gear box reqires adjustment, look on top of the gear box and watch the movment from forward to neutral, then watch the movment from neutral to reverse thet should have approxamatly the same amount of movement, if not adjust the link rod.

Aug 17, 2017 | Husqvarna Garden

1 Answer

MY HUSQVARNA YTH24K48 MOWER WILL BARELY MOVE FORWARD OR REVERSE. I CHECKED THE FREEWHEELING MECHANISM AND IT WAS WORKING PROPERLY. LOOKING UNDER THE MOWER AS WELL AS I COULD, IT SEEMED FINE.


sounds like the drive belt or belts are worn out. replace both in order for it to work properly .replacing one wont work. replace them as a pair.

Nov 05, 2016 | Husqvarna Garden

1 Answer

WILL NOT DRIVE FORWARD OR REVERSE


It sounds like the drive belt has slipped off a pulley. With fuel turned off, tilt the mower to one side- so the fuel cap is at the highest point of the tank, and cannot leak fuel out the breather hole. One belt will drive from the engine and the other end goes around an idler pulley. The other belt will drive from the axle to an idler pulley and will be slightly loose. This is the one that may have slipped from its position and not be contacting one or more pulleys when tightened. There should be a pair of pulleys, each being one side of the drive belt. Pressing the forward control should move one pulley onto the drive belt and simultaneously tighten the axle belt. Pressing the reverse control should engage the other pulley(on the opposite side of the belt) and also tighten the axle belt. This loose belt may have been bumped off one or more pulleys in the collision, and be sitting between the pulley and the guide/guard. With the ENGINE OFF, and the forward/reverse selector in neutral you should be able to force the loose belt back over the pulley.
Whether the forward/reverse mechanism drives the engine or axle pulley, the principle will be the same.

Apr 17, 2016 | Husqvarna YTH22V46 46 inch 22 HP Briggs &...

1 Answer

It will run backwards but not forward


If you are able to move in reverse but not forward, you need to adjust the levers. First you will need to elevate the rear wheels and set the neutral. This will then allow you to set the levers for proper forward and reverse movements.

May 03, 2015 | Husqvarna Zero Turn Mower Z5426

2 Answers

Has very little power in reverse.


sounds normal to me none of that type run fast backward

Apr 22, 2015 | Husqvarna 25HP Hydrostatic 54"Cut Garden...

1 Answer

My Husqvarna Rider 16c wont reverse - first it was slow in reverse then not at all


You need to check the cable, it is a push pull telescopic style so it is possible to get forward and no reverse, if it was a hydro problem you would not get forward or reverse, there is also timing gears on the forward and reverse pedal, you nee to make sure they have not jumped a tooth as this would reduce movement on the cable at the hydro

Feb 12, 2013 | Husqvarna Garden

1 Answer

Craftsman 20.5hp briggs and stratton will not go forward or reverse when I let off the clutch it starts to squeal and smokes fronm the drive belt


could be as simple as a worn out belt but look to see if there is a oil leak getting onto the belt

May 04, 2012 | Garden

1 Answer

My 42" Husqvarna (model #917.279240


Remove the center dust caps from the rear axles, start the tractor up and put it in gear and observe the axles, if one of them is spinning freely inside the wheel, you have lost the 1/4" square key that pins the wheel to the axle. Replace the key and you can go back to mowing. Hope this helped Tim

May 15, 2011 | Husqvarna Riding Lawn Mower 42 Inch Cut...

1 Answer

No forward movement but reverse works fine. Help?


More than likely the forward clutches are burnt,causing the no forward movement problem.Remove the transmission dipstick and smell the fluid,if it smells like burnt coffee then you need the transmission rebuilt.

Aug 02, 2009 | Chevrolet Blazer Cars & Trucks

Not finding what you are looking for?
Husqvarna Lawn Tractor 48" Deck, 23 Hp, Model# Yth2348 Logo

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Garden Experts

Phil Walker
Phil Walker

Level 3 Expert

608 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Husqvarna Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...