Question about GE WPRB8050D Top Load Washer

1 Answer

Clothes washer overflows

I have a washer that overflows only on the large & super capacity settings. The temp is set at cold/cold. I have continuity at the hot & cold solenoids, & at the water level sensor. Any ideas? thanks!

Posted by on

  • parchmentpro Sep 15, 2007

    Ok, thanks for your recommendation. I heard a click when I blew into the switch. Then I pulled the front cover off & refilled the washer on its large capacity setting. With the front cover off, I noticed the water overflowing from what appears to be an overflow pipe. I am thinking the pressure switch is faulty, so I have ordered a new one.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 60 Answers

Take the hose off at the pressure switch and blow through it if there are no restrictions then you have a faulty pressure switch let me know how you make out

Posted on Sep 12, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rinse cycle water temp


You may have a leaking hot water electrovalve, replace it.

Sep 06, 2016 | LG WT4870CW 27" Top Load Washer with 4.5...

1 Answer

I HAVE A MAYTAG PERFORMA WASHER MODEL#pav3240. the washer continues to fill during rinse cycle and overflows the top. If i turn to spin cycle water drains out and machine goes through cycles. it seems like...


Clean out the water-level switch air dome tube AND the the connection to the tub where the tube connects. It may well be full of gunk and not allowing the water level switch to react quickly enough.

Jun 06, 2017 | Maytag Washing Machines

1 Answer

Washer overflowed after moving Load Capacity Switch from Super to reset and then to Large load?


On this model of washer you have 4 separate components that could cause overflowing. The water valve, pressure switch, pressure switch hose & the air dome. If you have to turn the water off to prevent overflowing, I would recommend replacing the water valve. If you can turn the timer off & the water stops overflowing, I would recommend checking the pressure switch, hose & air dome.

Jan 16, 2011 | GE Washing Machines

1 Answer

Water continues to fill into the washer drum on the spin cycle.


Hi

You could have a stuck solenoid valve
Try this: Set the water temp on cold. Turn on only the hot water.
Does hot water try and fill the drum?
If so then there is a problem with the hot solenoid.

Next set the water on hot. Turn on only the cold water. Does cold water try and fill the drum ?
If so then there is a problem with the cold solenoid.

Jan 05, 2011 | Whirlpool LTE6234D Top Load Stacked...

1 Answer

I have a Kenmore Series 80 Super Capacity Plus Washer. It has 3 water temperature settings, Cold/Cold, Warm/Cold, and Hot/Cold. Warm is Cold and Hot is barely warm. I know I have very hot water as the...


Sorry to read about your problem, I hope this helps you out.

the inlet valves just open and close, if you have high cold water pressure, it will override the hot water. I suggest you turn down the cold water valve, until warm is kinda warm. your cold water fills will take longer, but you will have warmer water

I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck

4 Thumbs - Very Helpful
3 Thumbs - Helpful
2 Thumbs - Somewhat Helpful

Dec 30, 2010 | Kenmore 24032\24036 Top Load Washer

1 Answer

My Kenmore front loader sometimes fills with warm water on cold setting.


Most washer today use automatic temp. control fill valves. If water is too cold the control might mix in some hot to bring up to a preset temp. The same is true when control set for hot. For energy savings cold water will be mixed in to maintain a semi hot temp. Check with manufacture just to be sure.

Feb 03, 2010 | Kenmore 3.5 cu. ft. King Size Capacity Top...

1 Answer

GE super capacity heavy duty washing not filling w/hot water


On an older model washer, you probably have a bad water valve. (hot water solenoid coil electrically " open ") Newer models, now there's a can of worms. Some models use thermistatically controled water valves to limit water temps, so you may not be able to get true hot water. Also, if you are checking the temp as the machine fills, some models will only fill with cold if the lid is open. (safety feature) The only way to see what is really going on is to fill the machine with cold and use a thermometer to check the water temp, then, pump that out and fill (with the lid closed) with hot and check to see if that temp is higher. As stated previously, water temp may not really be " HOT " but may be warmer than " COLD ". That may be as good as you will be able to do, as all manufacturers are trying to reduce energy consumption. Thank your government.

Jan 21, 2010 | Washing Machines

2 Answers

Leaks occur in spin/empty cycle


I had the same problem, you need to turn the washing machine on it's side and look for a pin hole leak in the seam of the plastic holding drum on the bottom. I used a silicone sealant, "GOOP" , let it dry for 1 day and problem solved. It has not leaked in two years. good luck!

Nov 02, 2008 | Whirlpool 3.2 cu. ft. Plus Washer

2 Answers

Hot water continues to run after rinse, filling tub overflowing


sounds like you are right the water inlet solenoid on the hot side is sticking remove the hoses and clean th escreen out and the valve try agin with a fill on hot to see if it stops on a small load if not replace the water inlet valve

Mar 15, 2008 | GE WVSR1060A Top Load Washer

Not finding what you are looking for?
GE WPRB8050D Top Load Washer Logo

546 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

geapptech

Level 2 Expert

157 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...