Question about Office Equipment & Supplies

3 Answers

Cannon MP160 How to Print both sides of the Paper???

I looked through the setting but stil could not find both sides printing? "Cannon Pixma MP160" Thank Davin

Posted by on

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 186 Answers

Set Duplex Printing (Windows) For details on how to set duplex printing, see below: 1. Select 'Properties' from the Print dialog. Note: Properties may be indicated as Advanced, depending on the application software. 2. Click the Page Setup tab. 3. In the Printing Type section, select 'Normal-size Printing', 'Fit-to-Page Printing', 'Scaled Printing', or 'Page Layout Printing'. 4. Select 'Duplex Printing'. Note: When a media type other than Plain Paper, Photo Paper Plus Double Sided, or Postcard is selected in the Media Type menu, duplex printing cannot be performed. 5. Specify Staple Side. 1. The printer analyzes the Orientation and Page Layout settings, and automatically selects the best staple position. 2. Click the Staple Side drop-down arrow and select the setting. If you want to change the setting, select another value from the list. 3. If necessary, click Specify Margin... and set the Margin width 6. When the setting is completed, click the OK button at the bottom of the window. Note: If a media type other than Photo Paper Plus Double Sided is selected for Media Type on the Main tab: The document will be printed on one side of a sheet of paper when printing starts. When printing is complete, reload paper according to the displayed message and then click OK. The document will be printed on the opposite side. If Photo Paper Plus Double Sided is selected for Media Type on the Main tab: The document will be printed front and back alternately for one sheet at a time, when printing starts. Load the paper according to the displayed messages. 7. You will be prompted, while printing, to remove the printed page and reload it in the ASF. 8. Dependent on the number of pages to print, you will need to repeat step 7 until all pages have printed. Back to Top

Posted on Sep 12, 2007

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How about for a mac?

Posted on Mar 26, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The duplex printing option isn't available to us mac users, what a doosh bag

Posted on Oct 07, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my scanner cannon mp160 scan reverse image


Press the Resume/Cancel button.
- If paper is being fed at error occurrence,
the error is indicated after the paper is
ejected.
- If the error occurs, the print head
alignment values are not changed.
- After exit from the error by the
Resume/Cancel button, the automatic
print head alignment will not be re-done

Aug 23, 2011 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

How topaper load cannon mp 160 pixma


Hi there,

Loading Paper into your Canon MP 160 Pixma.

A) Loading Paper :
Follow this procedure:
1) Open the Paper Support, then pull out the Paper Support Extension.

2) Place a stack of paper (print side up) in the Auto Sheet Feeder, pinch the Paper Guide and adjust it to the left side of the stack.
* Set the Paper ThicknessLever to the correct position for the paper.
Note : Set the Lever to the left for most paper. When the Lever is set to the right, the confirmation message appears before the machine starts printing.
Important : Make sure the stack does not exceed the Load Limit Mark.


B) Loading Envelopes
Follow the following steps:
1) Open the Paper Support, then pull out the Paper Support Extension.

2) Prepare the envelopes for loading.
Important : * Press down firmly on the edges of the envelopes to make the folds crisp. Also, press firmly on the area that corresponds to the edges of the back flap.
* Remove any curling by holding the edges diagonally and bending them gently.
* If the edges of the envelopes are inflated or curled, place the envelope on a flat surface. With a pen, press down while moving it from the center toward the edges of the envelope.
* Ensure that no curl or puff exceeds 1/8 in. (3mm).

3) Place the stack of envelopes (print side up) in the Auto Sheet Feeder, pinch the Paper Guide and adjust it to the left side of the stack.
* Load the envelopes in the Auto Sheet Feeder with the short side down.
* Set the Paper Thickness Lever to the right.

Important : Make sure that the stack does not exceed the Load Limit Mark.

Hope this helps. PLease rate my response.
Thanks
Have a good day.

Dec 01, 2009 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

The paper will not feed on the left side


Every time I see these I find pens, candy, clips, other objects have fallen down the back where the paper goes. One lady picked up her printer, turned it upside down and shook it and a bic pen fell out, It worked fine after that.

Nov 05, 2009 | Canon PIXMA MP160 All-In-One InkJet...

2 Answers

MY MP160 FLASHES E AND # 3 ALTERNATELY


How to clear Error Code Canon printers MP150 MP160
CANNON Printers MP150/MP160 ERROR CODE


E2-2 No paper (ASF)
E3-3 Paper jam

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)
The number of the Reset
button pressing
LED Function Remarks

0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection

Aug 13, 2009 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

How to print envelopes on my printer


Use The Recommended Print Area For the best printing results, adjust the top and bottom margins of your document to within the recommended printing area shown below. Click on the paper size listed for the recommended print area settings: A4 / B5 / A5 / 4 x 6 / 4 x 8 / 5 x 7 / Credit Card, Letter and Legal, Envelopes (DL / COM#10)
Caution: When printing is performed outside the recommended printing area, the top and bottom edges of the paper may curl, the print quality may deteriorate, or the printed side may be smudged.
The printer has both the recommended print area and the printable area, according to the paper size.
05sj00144_01.jpg Recommended print area: This indicates the recommended print area.
05sj00144_02.jpg Printable area: Although this indicates the printable area, degradation of print quality may occur.
Note:
  • Set Borderless Printing to print without margins.
  • In Duplex Printing, the printable area of the paper's header is approximately 2 mm narrower than usual.
A4 / B5 / A5 / 4 x 6 / 4 x 8 / 5 x 7 / Credit Card
05sj00084_03.jpg Letter / Legal
05sj00084_04.jpg
Envelopes ( DL / #10 )
05sj00084_05_te.jpg



Nov 22, 2008 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

Faded printing


Check the settings in the printer properties and see if you have selected economy print..If you have, try switching to high quality..

Jun 13, 2008 | Canon PIXMA MP160 All-In-One InkJet...

1 Answer

Cannon mp 160 printer problem


Don't know if it's the same problem i had but its maybe worth a try. My paper went in a little, the wheels were turning but it didn't take the rest of the paper or print.
Someone replied to my problem, i tried it and it fixed 1st time. Also seems to of worked for others
Solution:- Use a piece of thin card, a magazine cover is what i used, make sure its A4 size then try to print something, as the paper starts moving push it through!! and hey presto it worked for me, everything printing fine now.
hope it works, let me know, Garty

Mar 20, 2008 | Canon PIXMA MP160 All-In-One InkJet...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

6,359 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

k24674

Level 3 Expert

8016 Answers

jasbo
jasbo

Level 3 Expert

2237 Answers

yadayada
yadayada

Level 3 Expert

78267 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...