Question about Epson Stylus Photo 1280 InkJet Printer

1 Answer

Printer Lexmark T630

Hello Mr., I have a printer Lexmark T630 and I have a problem I cannot solve it: when I assembled the chart network the printer posts an error message (900 Service RIP Software)

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 84 Answers

The error message is normally caused by either plugging accessories into the rip controller board or the engine board. In some models the board may be conbined. Or invalid or illegal commands sent from the printer. Try upgrading the firmware first. If that does not work you you may have a bad board. Hope this helps Click on the link below and select your operating system http://downloads.lexmark.com/cgi-perl/downloads.cgi?ccs=229:1:0:359:0:0

Posted on Sep 10, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix a 922 fuser error on my Lexmark T630?


I'm afraid replacing the fuserunit is the only option.

Feb 24, 2011 | Lexmark T630 Laser Printer

2 Answers

241 paper jam message


Lexmark T630 241 paper jam message - Indicates a paper jam from the pull down manual feed tray.


If you check to make sure and small fragments of paper are not hindering the operation of the switch. The switch is located on the left side of the tray and will be spring loaded. The switch should move freely without binding. Make sure no toner or dust is on the optical sensor assembly. See Diagram for location.



prefab_8.jpg

If the switch seems OK and the printer still reports an error, the printer will require professional care.

Jan 15, 2011 | Lexmark T630 Laser Printer

1 Answer

Hello i have a lexmark t630 and when it prints out of tray 2 it says change tray two and beeps. It will work normal if you hit the select button. What could it be?


the printer is telling you that the tray is reporting the wrong size paper. print the network menu from tray 2 if it prints out smaller than the page it will be reporting smaller than letter. if the bottom line of the outline is missing its reporting legal size paper. if you are running lettersize paper in the tray check on the left side of the tray half way down the drawer you will see a plastic snap in plate with 3 fingers the bottom 2 should be sticking out for letter size paper. you only have to be one of the small adjust teeth off to make the third finger stick out and report the wrong size paper this is a very common issue. look at the metal fingers that stick out of the frame of the options tray to make sure they are uniform and straight. if the fingers are set right and not damaged then the logic board in the tray assembly will have to be replaced

May 14, 2010 | Lexmark T630 Laser Printer

1 Answer

Lexmark t630 could not initialize due to a suspected lightning after a heavy rainfall


let me guess it stops about the 64mb range in the control panel? how did i do? any way change the network card static charges mess with the nvram chips. t3xx series are lexmarks that wont boot if the network card is not recognize. this should solve your problem. surge protector are always a goog idea on electronics have a great one

Nov 04, 2009 | Lexmark T630 Laser Printer

1 Answer

Lexmark T630 Error message "Paper Jam Remove rear cover." No paper jam...


Open the rear, there is one of the paper sensor actuators stuck. They are spring loaded and should spring back when pushed out by the paper.

Oct 14, 2009 | Lexmark T630 Laser Printer

2 Answers

Lexmark T630 frozen


Try to unplug the interface cable from the computer and power up the machine. It is likely the RIP card aka the controller card.
There are two types of controllers for this printer, non-network and network. Here are links to where you can purchase them:
Non-network
Network

Jun 06, 2009 | Lexmark T630 Laser Printer

1 Answer

Problem with a T630 Lexmark the message "Change Tray 1 Plain Lett


i take it that the printer does not go to ready? does you printer stop with 64mb in the display? if it does change the network card. if this isnt the problem some more info would be great

Mar 27, 2009 | Lexmark T630 Laser Printer

1 Answer

I am getting a message on the printer that says, "932 Service Printhead Error". The printer is a Lexmark T630. Help


The message indicates that the laser scanning head is defective. Lexmark calls it a printhead. Unless you want to spend a lot of money, it may not be worth fixing. A new part runs over a hundred dollars.

Dec 01, 2008 | Lexmark T630 Laser Printer

Not finding what you are looking for?
Epson Stylus Photo 1280 InkJet Printer Logo

1,735 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Office Equipment & Supplies Experts

Alun Cox

Level 3 Expert

2678 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2022 Answers

Are you an Epson Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...