Question about Sony DVP-NS57P

1 Answer

No picture no pic, no setup screen. I could see the movie was running and the remote was working. I initially plugged into the back of the tv and the jacks in front to no avail

Posted by on

  • 6 more comments 
  • magmath Dec 21, 2007

    i have no pic and i have voice only ,what i can do

  • jegatheesan Jun 28, 2008

    i have the same problem like above mentioned. There is no picture and the setup menu options are invisible but the dvd player is running. the screen is clear screen and able to hear the audio. i have my doubts that the remote may be locked. advice me how to getrid of this problem.

    thank u

  • notvmass Jun 28, 2008

    DVD running but obscured picture and no sound

  • nassmyer4 Jul 23, 2008

    My sony cd/dvd player at first showed a picture but accidently pushed something and now the screen is black and will not return to the picture. The remote work with brand new batteries. What does the "C" and "T" stands for in front of the timer. I thnk this must be the problem.

  • Anonymous Oct 22, 2008

    When I set this up I get no pictur.Iget sound and the disk is running.

  • burakerk Dec 05, 2008

    yes i did but,it is not working please any one help me...I can here the movie but there is video,only a black screen

  • akorcz Jan 03, 2009

    i have the same problum. i got the dvd player from my friend who has an hdtv and didnt use the red white and yellow jacks (which i have it running through) so i think its still set up to run through the hd jacks. i had no picture or sound and you could clearly tell it was running because of the display screen on the dvd player.
    i was messing around with the remote and pushed the PICTURE NAVI buttin then hit up a few times and pushed enter and that gave me sound. im going to mess aropund with it a little wile longer and if i dont figure it out im going to take it to my friends house and set it up for the standerd jacks thru his tv. if that works ill tell you how to fix the problum step by step

  • Anonymous Feb 03, 2009

    i have no pic and i have voice only ,what i can do



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 752 Answers

It is probably in "progressive scan" mode, which is only viewable on Component (RGB) inputs. Refer to manual to toggle back to "interlace" mode. Either that or you have the TV on the wrong input.

Posted on Sep 10, 2007

  • Mitch
    Mitch Oct 05, 2007

    So did you try my solution, or not?.......



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

We gave an Emerson 50 tv. The picture is too large for the screen. For instance, you can't see the score for the football game. On the remote, I adjusted with button on the remote for picture size.

Just initialize the TV. It will make it alright to factory conditions. Proceed.
1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [POWER]
button on the remote control unit.
3. Press [BACK] button to enter the Panel Key
Confirmation Menu.
4. Press any button on the touch sensor panel.
5. Press [INFO] button to proceed with the self check
6. Make sure to confirm the "INITIALIZED FINISH"
appears in the green screen.
7. Unplug the AC Cord and plug it back on again.

Sep 11, 2016 | Emerson Televison & Video

1 Answer

After initial set up and download, TV is displaying a hand on power plug picture with a red circle and line through it and a refresh symbol in light blue next to it, what does this mean?

Hi! and Welcome to Fixya!

What you have on the tv screen is a warning sign that your tv is currently updating its software. A hand holding a power plug with red circle on it says do not unplug the tv while its running the software update. The usual time for the update to finish is 60 minutes. It may took more than 60 minutes if you have a slow internet speed. This is normal especially if you are running the software update for the first time during the initial setup. The next time tv performs software updates it will take shorter time.

However, if the updates took more than two hours, the tv may be frozen. You can unplug and plug it back in and start from the initial setup again.

On some rare occasion, the tv may not proceed with the initial setup. You may have to turn off your modem to complete the initial setup. when initial setup is done, connect your tv to network and run software update again.

Let me know if you still have other questions.

Sep 07, 2015 | Sony BRAVIA KDL-55W802A 55" 3D 1080p...

1 Answer

Dvd player dvd does not show on tv screen

swop the TV back over to what ever you use for watching TV i.e.........HDMI 1 / HDMI 2 / AV 1 / DTV / etc.
Use the AV or SOURCE button on the TV's Remote, not your receivers remote or SKY remote.

Feb 12, 2014 | Pioneer BDP-LX52 Installed

1 Answer

I bought a new TV for my #2, but is says I'm not getting a signal when I hook it up to the cable. I have it on channel 60


You can go to TV 1 to make sure TV 2 is suppose to be set to channel 60. Did you run the auto setup on your TV? If you have already run the auto setup on your TV, unplug the receiver from the electrical outlet for 10 seconds and then plug it back in. This will make the receiver reboot and re-acquire satellite signal. Then see if you get a picture on your TV 2. If not, the last thing you can try is changing the channel from 60 to 73 through the receiver.

With your DISH remote at TV 1, press the Menu button - Main Menu will display on the TV 1. Then press 6 (System Setup), 1 (Installation), and 5 (Modulator Setup). On the Modulator Setup screen, move over to TV 2 Out and select Cable, then press select on the remote. This will automatically change the channel from 60 to 73. Highlight Done on the right and press select. Cancel out of each screen till you get back to the TV screen. Go to TV 2 and put the TV on channel 73. You should get a picture. I hope this helps.

Ray Calo
DISH Network

Feb 16, 2011 | DISH Network ViP622 DVR DTV Receiver /...

1 Answer

No tv picture

Call a professional and have the V setup again.

A1 Elmbrook Electronics Inc.

Mar 30, 2010 | JVC HD-52G787 52" Projection Television

1 Answer

No picture on initial portable dvd player

Make sure it's not turned to a different output, like it expects to be plugged in to a tv screen.

Mar 02, 2009 | Initial Televison & Video

1 Answer

Modified Picture Settings Reset Each Time TV Is Turned Off/On

Your TV may have been put into shop mode or demo mode. How to get out of "Shop Mode"

1. Press [Source] to get to the Air or Cable input on the TV or TV remote

2. Press [Volume +] once on the TV itself (not the remote)
Next step must be completed while the volume bar is still on screen

3. Press and hold [Menu] on the TV itself (not the remote) for about 7 seconds
If the screen flashes "Dynamic Mode", the process worked

4. Finally check whether the Picture Mode is "Shop Mode" or not after passing "INFO" on Remote Control. If picture mode is still in “Shop Mode” try the alternative way below

Alternative Method

Press [Source] on TV remote to get to the AIR or CABLE input
Press [Menu]
Press [Down Arrow] to highlight SETUP and press [Enter]
Press [Enter] again on PLUG AND PLAY
Wait 10 seconds
Press [Enter] to select ENGLISH (or choose an alternative language
Press [Right Arrow] to highlight HOME and press [Enter]
Press [Menu] repeatedly until you see the message ENJOY YOUR WATCHING
Confirm you are out of shop mode by pressing [Info] on the TV remote

Nov 09, 2008 | Samsung HL-T5687S Television

1 Answer

Cannot get the television to get out of fuzzy screen

  • hit the channel return button on the remote
  • hit the tv/video button on the remote
  • perform a channel scan through the remote menu
  • unplug unit for over an hour and plug back in, complete initial setup by following instruction on the tv.

Jun 25, 2008 | Philips Magnavox 27MS343S 27" TV

2 Answers


Yes your data card needs to be formatted or replaced. try formatting the card in the setup menu sometimes this helps. Hope this does the trick.

Mar 30, 2008 | Sony Cybershot DSC-T200 Digital Camera

Not finding what you are looking for?
Sony DVP-NS57P Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts


Level 3 Expert

102366 Answers

The Knight
The Knight

Level 3 Expert

75025 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides