How do you install the screen protector, have the protector and card to get rid of bubbles but no instructions

When installing the screen protector wipe the display with a damp cloth first, that will allow the air to escape when encouraged by gentle pressure.
Work the air out from the centre to the outer.

Use a hard edge like your drivers license or credit card. Work them slowly to the edges.
Next time use an alcohol wiper on the screen just before you apply the protector. This will help with removal of the bubbles.

Peel off or otherwise remove the screen protector, spray the adhesive (sticky side) with glass cleaner, then reapply the protector and use a credit card to roll out the air bubbles.

The screen should be cleaned thoroughly with an alcohol pad leaving no lint/dust. Then peel the back of protection screen off halfway, line up the peeled part on screen to your liking then use a credit card to push towards the end you haven't peeled yet while pulling the remaining backing and pushing the credit card from middle to edges.

Before putting the new protector on the screen must be completely clear of any dust/dirt. I use an alcohol wipe first to clean the screen then a clean microfibre cloth to dry the screen and wipe away any remaining small dust particles, then slowly apply the new screen protector like in the video above

1) Make sure device screen is ABSOLUTELY clean.
2) Make sure your hands, and workspace are also clean and lint free, then DOUBLE CHECK #1 above.
3) The pro's use a "wetting" solution to settle the protector onto the screen but NOTE ! wetness is generally bad for electronics !, so " a little, is good. More is NOT better!"
4) A small plastic squeegee is usually included with any "quality" protector kit. USE IT GENTLY! move the squeegee from the center toward the edges, pushing excess solution or bubbles as you go. Excess pressure stretches the protector and causes bubbles to form as the protector settles.
5) Once the protector is bubble free, in the correct place, and not hanging over the edges. LEAVE IT ALONE 'TILL IT DRIES AND SETS.

NOTES If your protector is one that uses an adhesive coating to hold it in place, DON'T TOUCH THE ADHESIVE SIDE WITH FINGERS (or anything else for that matter) because that's what makes dimples that trap bubbles. This process is proof of the saying "You only get one chance to do it right the first time!". If after the process is complete, and if you find there are still bubbles, you may try again but the likely chance of removing and replacing the same film without damaging it is very small. Fortunately, protector screens usually aren't too expensive (compared to the price of a damaged phone/tablet). Good luck!

Step 1: Clean your workspace. Be sure to get a flat, hard surface without a lot of fabric, liquid, dust, etc.
Step 2: Lay the phone down and clean it well with the cleaning cloth provided. Do not use any kind of cleaning fluid or water, but try to be sure that all fingerprints are gone. Especially be sure no dust or lint particles are on the screen. Before proceeding be sure that there are not a lot of dust particles gathering near you, vaccum and clean the area up a bit more if need be. You want as sterile an area as possible before continuing.
Step 3: Being careful not to touch the sticky side of the screen protector, peel back the tab where indicated. Hold the screen protector only by the sides and line it up with the phone. If you touch the sticky side of the screen protector by accident do not try to clean it off, you will only make it worse. Line up and let the screen protector fall into place from the top of the phone to the bottom. Some people choose to use a credit card or thin piece of plastic to smooth out bubbles as the screen protector makes contact with their device, however this is usually not recommended by the makers of the screen protectors or the phone. The choice is yours, but bubbles are meant to smooth out over time, so take that into consideration.
Steap 4: Once the screen protector is on the device if it is straight and you can see bubbles but no lint or dust beneath it, you are successful, give it a few days for the bubbles to dissipate. If it is not on straight, you may be lucky enough to be able to lift it up and place it better without fault, however this is risky. If lint or dust has gotten between your phone and the screen protector you have likely failed, there is little recourse from here, other than removing the screen protector, cleaning the device, and trying with a new screen protector altogether.

To lift the protector off one edge of the display, place a sticky tape on the edge of the protector and then pull on the sticky tape to lift off the protector.
Lift the screen protector from one edge, peel it back to the last bubble then re-fix the protector in place by slowly apply pressure across the proctector as you push the protector onto the display making sure no bubbles forms between the display and the protector.

Hi,
Once the screen is scratched there is no easy or affordable way to replace it...the best thing to do is to install a plastic screen protector as soon as you buy a new phone... they cost a few bucks, but are well worth the price...
Many popular phones have screen protectors made in exactly the right size for the phone...but there also are generic protectors that you can easily cut to fit any phone...

Be very careful and patient when installing the screen protector so that you do not get bubbles under the plastic...have a small piece of plastic or a Popsicle stick handy to smooth out the protector as you install it.

heatman101