Light is on only on back side, not front

Bad wiring or a corroded bulb socket. Check the wires carefully especially at the socket.
Good luck...

The Headlight Assembly is not difficult to remove but you do need to be careful NOT to pull on the Headlight Assembly and break the clips

1. Open the S60's hood and locate the pin that is behind the headlight assembly of the bulb that needs replacement. The pin has a handle on the top. Pull the pin straight out of the headlight assembly.

2. Push on the back of the headlight assembly until it comes out the front of the S60. There is an electrical connection on the back of the assembly; unplug the connection.

3. Press on both clamp on the assembly. The clamps are on either side. Push them in together so that the cover releases.

4 Uncover the bulb by pulling on the small plastic cover that covers each bulb. Push the visible wire aside. Pull the bulb straight out.

5 Push a new bulb in and push the metal wire back over it to secure the bulb in the assembly. Push the covers back on.

6. Reconnect the electrical harness to the assembly and push the assembly back into place. Push the retaining pin all the way back down into place.

Look in front of light cover,and remove screws,and remove light assembly,twist our terminal,remove bad bulb and install new...Some cares offer enough room to simply twist out terminal from behnd to install new bulb then twst back in..Best to change both bulbs

the head light bulb is on the back side
there is two locking pins under hood holding the assembly in
rotate 1/4 turn and pull up pull assembly put and unplug
remove retainer ring and remove bulb
assemble in reverse test new bulb before mounting light assembly back in

If there are visable screws around the tail lite lens yes they come out and just screw off the bulbs socket than the bulb,,,If no visable screws than the should be a panel on in side of vehcle back side that comes out for access to the lights.

I believe the plastic cover has either screws or clips on both sides just pry easy under pressing inward.. slowly haste makes waste with these little things... good luck bulb should pull straight out of the socket after twisting it out of the cover

Hello,

Unplug the Whirlpool refrigerator from the electrical outlet.
Step 2
Locate the bulb on the inside of the Whirlpool refrigerator.
Step 3
Remove the light cover. Usually these just snap off, but, on some models, they may need to be unscrewed. Use your screwdriver to unscrew the light cover retaining screws (if required).
Step 4
Unscrew the old light bulb.
Step 5
Screw in the new light bulb.
Step 6
Replace the light cover. Plug the Whirlpool refrigerator back in. Test your new light bulb.
Also note that the below can also work

Unplug refrigerator or disconnect power.
Slide the light bulb cover toward the back of the compartment to release it from the light assembly.
Replace burned-out bulb(s) with appliance light bulb(s) no greater than 40 watts.
Replace the light bulb cover by inserting the tabs on the cover into the liner holes on each side of light assembly. Slide the cover toward the front until it locks into place.

NOTE: Do not force the cover beyond its locking point; doing so may damage the light cover.
Plug in refrigerator or reconnect power.
To change the freezer light bulb:

Unplug refrigerator or disconnect power.

NOTE: You may need to remove the upper freezer shelf or basket to access the light assembly.
The light bulb cover opens from the back. Firmly press forward on the notches in the back of the cover and pull down the cover.


Remove the cover and replace the burned-out bulb with an appliance bulb no greater than 40 watts.
Insert the front tabs of the cover into the liner and snap the back portion of the cover over the light assembly.
Plug in refrigerator or reconnect power.

Good luck in applying the solution

Some models are different...I hope this helps.

Replacing Light Bulbs
To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before replacing light bulb. After replacing light bulb, reconnect power.
To avoid personal injury or property damage, observe the following:
• Allow light bulb to cool.
• Wear gloves when replacing light bulb.
Fresh Food Section
(style of light shield varies)
1. Slide clear light shield toward back of compartment to release from light assembly.
2. Remove light bulbs.
3. Replace with appliance bulbs no greater than 40 watts.
4. Replace light bulb cover by inserting tabs on light shield into liner holes on each side of light assembly. Slide shield toward front of refrigerator until it locks into place. Do not force shield beyond locking point. Doing so may damage light shield.
Freezer (style of light shield varies)
1. Reach behind the light cover.
2. With firm pressure, press forward on the notches at the back of the cover and pull down the cover will open from the back.
3. Remove the cover.
4. Remove light bulb
5. Replace bulb with appliance bulb no greater than 40 watts.
6. Insert front tabs of light cover into slots in freezer liner and snap rear portion over light assembly until rear tab engages.

Ric

Unscrew 3 - 4 screws on the front tire fendor cover close to your side marker light. Pull the fender cover out, use your other hand to reach the side marker light. Using twist and pull the light set out. Replace a new light bulb. Replace everything in a reverse order.