Question about Jenn-Air JGS8750 Gas Kitchen Range

3 Answers

Jenn Air model S176W

I too had the error code of F1 coming up on my Jenn Air stove - managed to get another year out of it - until now. The circuit board has been beeping so much that I removed it from the stove all togehter. Having done that I noticed a burn mark on the plastic around the display - wondering if heat from the stove over time caused this problem? Anyway - now it's a question of getting a whole new stove for $2,000.00 or paying $200.00 for another circuit board and not knowing if that will work or for how long. Doesn't look promising from what I read on the net. Any suggestions?

Posted by on

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 121 Answers

Unfortunately whit the technical comes technical problems. Circuit boards are repeated problem in my profession. Replacing the circuit board will fix the oven, but also inspect the door gasket to insure a tight fit. Depending on the age and condition of the oven you may consider replacement.

more asst.
eboukater@gmail.com

Posted on Sep 24, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 725 Answers

Heat and moisture (steam) kills the electronics in any control. but if the mark are on a circuit then there was a short in a circuit. I would check the series if your stove( first two numbers in the serial number)if it is a early series. for sure that they have make improvements in the control. And a Replacement controls will have all the improvement and revisions. good luck and let me know what you do..kraztech

Posted on Sep 08, 2007

Ad

This model has no heat shield to effectively protectI the control board and as far as I can recall I believe there is no fan to exhaust the heat out but just uses a convection way of eliminating excess heat. I know someone who bought a second board but only after only a litlle over a year it went again with the problem. It's time to buy a new one.

Posted on Sep 09, 2007

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

VANMAN69
  • 23 Answers

SOURCE: F1-1 error on Jenn-Air Range

if it is the stove that is in the picture the fault codes are in the door under the oven door.

Posted on Jun 02, 2007

  • 5 Answers

SOURCE: Jenn air range model SCE30600B error code FC

replace the entire range: Jennair does not know how to design, make, or program electronics. It makes steel boxes that provide heat but electronics - that's not within their ability. Buy a Kenmore or a GE and your beeping problem will go away.

Posted on Aug 31, 2009

SOURCE: Jenn-Air SCE 30600, oven error codes F1 and Probe

An F-1 error code on your model means the element was energized when it should not have been, A shorted interconnect harness or failed power relay board.

A probe indication could be a failed meat probe jack or bad harness in a unit that has one. In a unit without a meat probe, suspect a bad board.

Both conditions would warrant bringing in a tech.

Before you do, turn off the circuit breaker fot 3 miutes and turn it back on. This will reboot the boards. If problem persists, the call a service tech.

Posted on Nov 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I cant get my stove to stop beeping. f1 error


You need to get the exact model number and make of this stove. Get ready for a bad circuit board to be the culprit, because electronic stoves are pretty much unfixable by mechanical means and the problem usually comes from a bad capacitor, corroded or overheated circuit board.

When you get your model number and make, go to YouTube and just type in your model stove and ask "how to repair a F1 error code on a blah blah stove". There are so many video's there on how to repair things with actual instructions and pictures. It's great.
Use this link to close in:
https://www.youtube.com/results?search_query=repairs+to+appliances+or+stoves

Jan 27, 2015 | Kitchen Ranges

1 Answer

Jenn-Air Range displaying Error F1-8


Did not find an error code "F1-8"
I did find these. Seems that about everything that can go wrong with a Jenn Air is related to the clock.


https://www.repairclinic.com/RepairHelp/FaultCodes/26/Range-Stove-Oven

Sep 22, 2017 | Jenn-Air JES8850AAS Electric Kitchen Range

1 Answer

I have s176w jennair range that flashes and F1 signal and a makes a buzzing sound when I turn any burners on


F1 usually go back to the electronic control board. Unplug and replug the power back on. If error code comes back, replace board.
You might want to check all wires going to the board for anything unusual...make sure they are properly attached etc.

Oct 23, 2013 | Jenn-Air Kitchen Ranges

1 Answer

F1E1 error happened repeatedly, jenn air says cut




F1 - E1
EEPROM checksum error
1.
Disconnect power for at least 30 seconds.
2. Re-apply power and observe for
at least one minute.
3. If code re-appears, replace control board (also
called ERC or clock).

Note: Applies to all F1-E...
codes except F1-E3.

Read more: http://www.appliancepartspros.com/repairtips/repairtips_appliance+fault+codes.aspx#Jenn
Air Range / Stove / Oven Fault Codes#ixzz19GMNtS3r


http://www.appliancepartspros.com

Dec 24, 2010 | Jenn-Air 27 in. Electric Single Wall Oven...

1 Answer

What des error cde F1 mean on a Jenn-Air D156 drp-in range


JENN-AIR
'Newer Style' Range/Stove/Oven Fault Codes Failure
Code
Condition Check/Repair F1 Power to element relay energized during time of day display Wiring harness shorted or change power relay board (PRB)

Note: for double ovens, change second oven board

JENN AIR
Range/Stove/Oven Fault Codes Failure
Code
Condition Check/Repair F1 Defective touch pad or membrane Replace touch pad or membrane (this problem is usually the touch pad)

Mar 22, 2010 | Food Processors

1 Answer

F1 error code and constant beeping and oven shuts off.


Hi gwhiz03,

If you are having error code F1 with your Jenn-Air double wall oven this is because you have a defective touch pad or clock (ERC). This simple test will help determine whether the ERC (Electronic Range Control or Clock) or the touch pad is defective when F1 error code is present.

Note: Some models incorporate the touch pad in to the ERC as a single assembly, in which case this test is not necessary. Simply replace the ERC (Clock).

Warning: If you feel in any way uncomfortable performing this test or making this repair, please contact a qualified appliance repair technician.

1. Disconnect power to the range (unplug the range power cord or turn the power off to the range at the circuit breaker). It is very important that the power to the range has been disconnected, so please double check before continuing.
2. Gain access inside the control panel.
3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC.
4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was.
5. Turn the power back on.
6. Wait for at least one hour to see if the F1 code comes back (usually accompanied by a beeping sound).
7. If F1 comes back, replace the ERC. If it does not, replace the touch pad.

Hope this helps.

Thank you for using FixYa.

Feb 10, 2010 | Jenn-Air WW30430P Stainless Steel Electric...

1 Answer

Model S176W Jenn-air F-1 code flashing and beeping


Not sure what an F1 code is on that unit, but an easy check here,
shut off unit at breaker, remove face and unhook touchpad (ribbon) from the ERC. Turn the breaker back on, If the error code stops and it doesn't beep, the touchpad is most likely the problem. If it continues to beep and throw code, could be the Erc, (or something else telling the erc somethings wrong.) without knowing the F1 fault code, I wouldnt know where to start looking!

I would probably recommend a tech to reinstall the new Erc and or touchpad. Most new electrical components require extreme care when handling/installing, and a tech will know the proper procedures. Good Luck!

Sep 12, 2009 | Jenn-Air JGS8750 Gas Kitchen Range

1 Answer

Jenn air range stove jsg8750 have a f1-7 error code


Hi there...
Error F1-7 means --
Replace touch pad or clock assembly (also called the ERC).
Good Luck!!

Jan 29, 2009 | Jenn-Air JGS8750 Gas Kitchen Range

1 Answer

F1 Failure , need to know how to advance the clean timer to get unit to unlock


Hello welcome to fixya,


Below I pasted the fault codes for the two different years of this range.

To diagnose these difference you will need a hands on tech !
this is not an easy thing to determine

JENN AIR

Range/Stove/Oven Fault Codes
Failure
Code
Condition Check/Repair F1 Defective touch pad or membrane Replace touch pad or membrane (this problem is usually the touch pad)

JENN-AIR
'Newer Style' Range/Stove/Oven Fault Codes

Failure
Code
Condition Check/Repair F1 Power to element relay energized during time of day display Wiring harness shorted or change power relay board (PRB)

Note: for double ovens, change second oven board

Dec 08, 2008 | Jenn-Air SVE47100 Slide-In Electric...

3 Answers

F1-1 error on Jenn-Air Range


if it is the stove that is in the picture the fault codes are in the door under the oven door.

Jun 01, 2007 | Jenn-Air JGS8750 Gas Kitchen Range

Not finding what you are looking for?
Jenn-Air JGS8750 Gas Kitchen Range Logo

794 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jenn-Air Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal De

Level 3 Expert

2694 Answers

Craig Butler
Craig Butler

Level 3 Expert

1723 Answers

Are you a Jenn-Air Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...