Question about Projection Televisions

1 Answer

Sennheiser hookup to noncompatable Samsung DLP TV

Samsung TV does not have a jack to connect a sennheiser TI250 unit. Tried work around by going thru an amplifer (TEAC AG-V8050) to power/feed sennheiser signal. This was set up by another person and I didn't check out the specific hookup-dumb! It has stopped working and I can't figure out how the hookup worked-none of the manuals cover this.Does anyone know about solving this problem? My wife is fighting cancer with a severe hearing loss and this is her LIFE SUPPORT!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,139 Answers
Re: Sennheiser hookup to noncompatable Samsung DLP TV

Ok if I understand what you are saying. You are going from your TVs audio jack into an amplifier TEAC AG-V8050 and then into the Sennheiser T1250 unit? This is done to amplify the sound so your wife can hear the TV via Infared into headphones I am guessing. The connections would have to be as follows. TV RCA jack (Installed by someone to TV audio Output section, most likely the speaker) to the Amplifier TEAC AG-V8050 via RCA cable then from the Amplifier via RCA cable to the Sennheiser TI 250 IR Transmitter. The transmitter then takes the audio input and turns it into a digital signal which is transmitted via IR to headphones which your wife is using. First of all the amp TEAC AG-V8050 is not needed. what happend here is the person doing the installation took sound off of a preamp to avoid having to deal with the TV volume control. This works but it makes matters harder. So here is how you troubleshoot this problem: 1) Disconnect the amplifier and plug the RCA jack of the TV into the RCA jack of a set of amplified Mono headphones. (This is to determine if sound is coming from the TV) If not the problem is in the TV audio section and you will need to take it to a TV repair shop. 2) If audio is coming through the headset the trouble is in the amp or the sennhiser unit. To test the sennhiser unit: plug the sennhiser into the audio out of a VCR and listen in the headphones for sound. If you have sound, the sennheiser is good and the problem may be in the amplifier, but if you do not have sound the the sennheiser is bad. 3)Connect the audio out of the VCR into the audio in of the amplifier and plug the output of the amplifier into the sennheiser which tested good with just the VCR alone. If no sound is present then the amp is your culprit. Once you find out which component is the problem, I would suggest finding a rapair shop here on FitYa to repair your unit or having an electronics technician come to you to fix the bad component. This should help, Thank you, Shuttle83

Posted on Sep 07, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Samsung dlp has static

I have seen this happen quite a bit. For some reason the input (cable jack) works loose from the board. I would try running your source signal (cable/dish) to another input on your tv...such as S Video/HDMI/Composite or whatever you have available.

Jan 07, 2013 | Samsung DLP HL-P4663W 46" Rear Projection...

1 Answer

Lamp replacement troubles

It is not a correct replacement lamp. Look for the "lamp code" on the side of the set. Make sure the replacement lamp has the same number.

May 19, 2009 | Samsung DLP HL-P4663W 46" Rear Projection...

1 Answer

No sound, just clicking noise

Is your TV a SAMSUNG DLP TV Model HLN437W Rear Projection Digital HD?


mobile phones: 1-888-987-HELP(4357)
  • Mon - Fri : 7am - 9pm (CST)
  • Sat : 9am - 6pm (CST)

digital HDTVs: 1-800-SAMSUNG (1-800-726-7864)
  • Mon - Sun : 9am - Midnight (EST)

printers: 1-800-SAMSUNG(726-7864)
  • Mon - Sun : 24hrs

IT Products for Business: 1-866-SAM4BIZ(726-4249)
  • Mon - Fri : 9am - 9pm (EST)

All other products: 1-800-samsung (1-800-726-7864)
  • Mon - Sun : 9am - 9pm (EST)

To see PHOTOS of REPLACING a SAMSUNG DLP TV ballast go to:

Hope this is helpful.

Good Luck!
Jack iaria

Nov 25, 2008 | Samsung HLN437W 43" Rear Projection HDTV

1 Answer

Samsung sam HLN507w model xixaa won't power on

I got frustrated with the tv and (after advice from a friend) banged on it somewhat gently with my hand. Now it turns on! My friend claims that their downstairs tv acts the same way and a few gentle taps do the trick every time. Go figure.

I'm not completely satisfied with this solution and don't think it will work forever, but so far so good.


Oct 07, 2008 | Samsung HLN507 50" Rear Projection...

2 Answers

Samsung DLP vertical black lines

I did some reading on this. They said its caused by a faulty DMD board. I understand it's costly... around $700 to replace. Still looking for a cheaper avenue...

Apr 28, 2008 | Samsung HL-P5063W 50" Rear Projection HDTV

2 Answers

Samsung HLP5063WX/XAA 50" DLP

Here is a site for ColorWheel replacement, which is what you need to do if you hear that screeching or fan running noise coming from your TV. Sometimes the wheel just explodes which gives you no picture.

Sep 29, 2007 | Samsung HCM4215W 42" Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1187 Answers


Level 3 Expert

56631 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides