Question about Kenmore Elite HE4 Electric Dryer

1 Answer

Electric kenmore he 3 dryer what is code E-1 mean

My dryer starts but then stop after a few minutes and the code E-1 is displayed. I can restart it several times until the clothes are dry, but this beginning to become a real problem.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 240 Answers
Re: electric kenmore he 3 dryer what is code E-1 mean

This code is for a part called a "Thermistor". Its like a thermostat for an electronic machine.

Posted on Sep 07, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Start for just 1/3 second then stop with error PF ?

Hey Andy, thank you for your post!
From what you have described your Frigidaire dryer, GLEQ2152ES, is running for a few seconds and then displaying an error code of "PF". The error code of "PF" means there is a power failure and this could be an issue within your control panel or power source. I would suggest performing a reset, this could help clear our any miscommunications within the panel, and you can do this by disconnecting the power cord for at least ten minutes. I hope that this information is helpful towards your repair. -Matt

Feb 17, 2016 | Frigidaire GLEQ2152ES Electric Dryer

2 Answers

82822 / 82824 / 82826 Electric Dryer: kenmore HE2 electric dryer, beeps and all display ...

F01 - There may be an internal problem with the control, attempt a Hard Reset.

Hard Reset - In some cases the control can be non-functioning or may not accept activation from the control panel. To clear and restart the control follow the these steps:

* Unplug or turn the circuit breaker off for 30 seconds.
* Reconnect the unit to the power source by turning the breaker back on or plugging the unit back into the wall outlet.
* Press the Pause/Cancel/Stop button twice to clear the "PF" in the display.
* Start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button until the machine starts.

The F01 generally indicates a failed electronic machine control board.
This error code can sometimes be caused by a glitch or power surge through the electrical lines.
You may be able to clear this code by unplugging the washer for 5 minutes.
If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.

The procedure for accessing and replacing this control board is shown in this image...,wkwdftgtbkdgfrwxgtqsskgwtqkq,vi/ksrttqdqrxkssrqtgsd/1/1303472/5961857/image12917img-or.jpg

Be sure to unplug the washer before accessing internal components.
When you access the control board, I recommend transferring the wires from the old control board to the new replacement control board one connection at a time.
Once you have all of the wires transferred, remove the old control board and mount the new control board in the washer.
Reassemble and test the washer.

The "F01" error code indicates a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU.
The "F01" can also be displayed if the onboard "Pump Driver" fails to activate.
Generally in order to correct this failure will require replacing the CCU.
There is no way to test and verify if the control board has failed.
The technical data sheet basically states to replace the CCU.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

May 17, 2010 | Kenmore 82822 Electric Dryer

2 Answers

Kenmore he2 electric dryer error code f-01

always unplug for 10 minutes and retry first.

Jun 12, 2009 | Kenmore 82822 Electric Dryer

1 Answer

Blinking error codes?

Unplug the machine for 30 minutes , plug it back it, start it for 1 minute, unplug it again for 5 minutes then plug back it and it should work. If not then write back with the error codes so further diagnostics can be done

Apr 08, 2009 | Kenmore 62602 Electric Dryer

2 Answers

Kenmore Elite Oasis Steam dryer runs but gets a F 40 code and stops. Just plugged it in to do my first load. Tried pulling out and checking lint in vent. It seemed to over heat the first time then sat a...

After just now calling the service center it seems that unplugging the machine for 30 seconds or so will reset the control panel. The F 40 code means the signal wasn't working in the machine and resetting it solved the problem. Kind of like when you have to unplug the computer sometimes.

Dec 31, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore Dryer 90 Series will start but suddenly stop...

what starts and stops? the entire dryer or maybe the drum? Do you do anything to make it restart other than pushing the start button? This initially sounds like a temperature switch is opening and resetting after it cools. If you can describe the problem a little more in detail it would help.

Jan 27, 2008 | Kenmore 659 Electric Dryer

1 Answer

Kenmore dryer 417.84072300

Check you circuit breaker. Even if it doesn't look tripped reset it anyhow. This is a power interrupt code.

Dec 04, 2007 | Kenmore 84072 Electric Dryer

2 Answers

E-1 light

check owners manual should have a code listing. Have you checked the vent and venting

Oct 17, 2007 | Kenmore Elite HE4 Electric Dryer

3 Answers

Dryer shows f44 error

007, F44 is a motor control electronic failure. Couple of things you can try. 1. Unplug the dryer for 1 minute. Plug it back in and see if the error stops. 2. Under the consol there is a 3 wire harness that runs between the two control boards. Try reseating this harness. If that doesn't work, you will either have to call for service or do some detailed trouble shooting. Catriver, post back.

Aug 17, 2007 | Kenmore 67082 Electric Dryer

Not finding what you are looking for?
Kenmore Elite HE4 Electric Dryer Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides