Question about Maytag SAV5710 Top Load Washer

2 Answers

Belt installation hello i have a maytag neptune front loader mah6500aww how do i install the belt on this washer this is the fourth time i need to repair this washer have no money to keep doing this warranty ran out help

Posted by on

  • Anonymous Mar 12, 2014

    I am trying to run the self diagnostic codes on a mah6500aww washer

×

Ad

2 Answers

Geoff Siegel
  • Level 2:

    An expert who has achieved level 2 by getting 100 points
    MVP:

    An expert that got 5 achievements.
    Governor:

    An expert whose answer got voted for 20 times.
    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 164 Answers

Repacing the belt on a neptune is simple. unplug the unit and move it away from the wall.. now remove the 4 screws holding the access panel in place. loop the belt over the end of the motor shaft so that the grooved side of the belt catches the grooves on the shaft. now simply feed it around the tub pulley. if you find the belt keeps coming off you might have a bearing problem tht has caused the tub to shift. look for fine plastic powder, almost dust like, that would be the pulley eating into the back of the tub

Posted on Sep 05, 2007

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

What kind of problems have you had in the past? Have you ever needed to replace the belt before? I imagine the back comes off to access the drive pulley and motor pulley. once you get the back off just examine which way the pulley is reaved and what you need to remove, if any, to get the belt on.

Posted on Sep 05, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

6ya.com

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size washing machine is this
Your Maytag Neptune MAH6500A Front Load Washer has dimensions:

Width : 27"
Depth : 29"
Height : 42 1/2"
Capacity : 3.34 cu. ft.

http://www.ajmadison.com/cgi-bin/ajmadison/MAH6500AWW.html

May 22, 2014 | Maytag Neptune MAH6500A Front Load Washer

1 Answer

How do I check the drain pump on Maytag neptune washer
I have a matag front load washer MAH6500AWW the door won't lock it just clicks

Apr 07, 2012 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

I need to download a owners manual for a maytag neptune washer mah6500aww we don,t have any trouble. we just got one and it don,t have a manual
give me your email address and I will email you a pdf copy

Mar 27, 2011 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

I have a maytag NEPTURE MODEL # MAH6500AWW front loading washer, the control light START BUTTON IS FLASHING AND WASHER WILL NOT START
you can try to reset it by unpluging for about 15-20 mins to let it reset itself. hope that works.

Dec 21, 2010 | Maytag Neptune MAH6500A Front Load Washer

1 Answer

Maytag washer mah6500aww 2003 When I start washer the door lock light comes on then off and on again before it will wash. When time to spin and drain the time goes to zerro and will not drain water out.
u will need to unplug it for about 15 mins to let it reset

Dec 01, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

My maytag neptune front load washer (MAH6500AWW) will not start, the start/pause button just blinks and when i press it it beeps at me. I don't know whats going on!!
control board bad

May 06, 2010 | Maytag Neptune MAH6500A Front Load Washer

2 Answers

Neptune - has Lr displayed where time remaining for wash usually displays. Doesn't finish.
Hello there
The LR error on your non-spinning Maytag Neptune is usually, though not always, accompanied either by a burn spot or a blown fuse on the Motor Control Board.

Burn Spot on a Maytag Neptune Washer Motor Control Board (click to enlarge)
Blown Fuse on a Maytag Neptune Washer Motor Control Board (click to enlarge) Either way, it means just one thang: a new motor and motor control board kit are in your future.

Dec 25, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

MAYTAG MAH6500AWW-WASHER WILL NOT AGITATE/SPIN
Hello,

Check out the motor control board near the floor on the right side. These have a high failure rate on the Neptunes. Maytag redesigned both the motor and motor control board to be more reliable. While inspecting this board, you are looking for a blown 10 amp fuse and /or burnt components. If you have either... then you will need the the new 12002039 motor conversion kit which includes the motor, motor control board and the wire harness.

See http://www.neptunehelp.com/index_files/Page667.htm.

This kit takes about an hour to install.
Don't forget to replace your door latch wax motor. See www.neptunehelpsong.com to hear a funny song explaining the faulty door latch failure.

Feb 07, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

MAYTAG MAH6500AWW-WASHER WILL NOT AGITATE/SPIN
This is a frontload Neptune. I think you will find that the motor control located in the bottom right front of the cabinet is bad.

Feb 07, 2009 | Compaq Presario 5000 PC Desktop

2 Answers

Maytag neptune modle MAH6500AWW
it is saying locked rotor situation, could be a loose connection at the main board, at the door switch or the motor is bad, bet motor kit # for motor and board 12002039 good luck with the repair

Apr 12, 2008 | Maytag Neptune MAH6500A Front Load Washer

Not finding what you are looking for?

View Most Popular

SAV5710 Top Load Washer

  • Washing Machines

Related Question

What size washing machine is this

  • Maytag Neptune MAH6500A Front Load Washer

Open Questions:

0 Answers

how to replace belt on Model maw 5000

Apr 27, 2014 | Maytag SAV5710 Top Load Washer

0 Answers

I have a Maytag Bravos washing machine model #MVWX500XW1. Recently the spin cycle was sounding louder than usual like a bearing going out. By the weekend the clothes would not spin. I opened it up to find oil from the drive motor all over the motor and belt. I replaced the motor and everything was working again except for the same loud bearing noise. Is there a main bearing for the basket and is this common for this model. It's only 2 to 3 years old

Feb 12, 2014 | Maytag SAV5710 Top Load Washer

0 Answers

model GTWN4950LOWS very noisey in spin cycle My GE washer sounds like a jet plane taking off when in the spin cycle. It is model GTWN4950LOWS Serial # AT116994G

Dec 10, 2013 | Maytag SAV5710 Top Load Washer

0 Answers

maytag top load has very loud noise when it goes to spin cycle. the whole tub bangs into the side and back cabinate of the washer The tub actually hits the side and back of the washer. The washer is level and the load is evenly distributed

Nov 25, 2013 | Maytag SAV5710 Top Load Washer

See all Maytag SAV5710 Top Load Washer Questions

Related Topics

Maytag SAV5710 Top Load Washer Logo

195 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

Maytag Atlantis MAV6000 Top...

Maytag Neptune MAH9700 Front...

Maytag Centennial 3.2 cu. ft....

Maytag SAV5710 Top Load Washer

Maytag Neptune FAV6800AW Top...

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...