Where is the power source for the 2616d? - NorStar Meridian M2616D Corded Phone (normerm2616d)

The wiring for a 1500a Li jump starter should include the following components:1. A power source such as a battery, generator, or other power source.2. A power cable to connect the power source to the jump starter.3. A circuit breaker to protect against any over-current conditions.4. A relay to control the flow of electricity from the power source to the jump starter.5. A charging port for connecting the jumper cables to the jump starter.6. A set of jumper cables to make the connection between the power source and the jump starter.7. Safety features such as a fuse, circuit protection, and/or a safety switch to ensure that the jump starter is not damaged or over-powered.

If under your own power source, vehicle is not starting...
then you connect an alternate power source, and it starts (as you said - right up) then your power source is bad!
Power Source = Battery

http://waterheatertimer.org/How-to-add-switch.html
http://waterheatertimer.org/Basic-household-circuit.html
http://waterheatertimer.org/Install-owb.html

Gene

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

You may try this; Turn OFF the laptop, remove the power sources (ac adapter and battery). Without power sources, hold power button 10 secs. Put back the power sources, and power ON the NB.

Hello,


You may try this; Turn OFF the laptop, remove the power sources (ac adapter and battery). Without power sources, hold power button 10 secs. Put back the power sources, and power ON the NB.

Have nice day :)

If you know the power source is good then it's either a fuse, the cable itself or the power supply for the monitor.

You have a bad power supply.

The computer power supply is a central point for the compute powere BUT it divides the power into severl "flavors" it creates a source for hardware line drives but it also creates a source for the mother board which is a different coltage and current level fro the hardware source.

The suspect is that teh compents in teh powersupply that bracch the mother board sources is dead.

OKSolution 1:

1. Turn off power and unplug from power source.
2. Open right side of printer.
3. Disconnect,by pulling gently, both white flat ribbon cables off the main circuit board.
4. Plug in power source and turn printer on. Wait till you get a error message and push "Ok".
5. Unplug power source.
6. Reconnect the flat ribbon cables by aligning and carefully pushing into the conectors on the main circuit board.
7. Plug in power source and turn printer on.

Solution 2:

1. Turn off power and unplug from power source.
2. Open right side of printer (looking at the front).
3. Disconect,by pulling gently, the flat ribbon cable off the main circuit board that is the smaller of the two.
4. Plug in power source and turn printer on. Wait till you hear no more movement from inside from unit booting up.
5. Press both cancel and power button at the same time.
6. Message on printer screen will be, "Enter Special Key Combo".
7. Push keys; Left-Ok-Right.
8. When printer screen changes, scan through and look for "System Menu" and push "Ok"
9. Scan agan and look for "Clean Derivative" and push "Ok". Wait for 1 minute.
10. Scan agan and look for "Clean Firms" and push "Ok". Wait for 1 minute.
11. Press "Cancel" 4 times
12. Turn off power and unplug from power source. Wait for 2 minutes.
13. Reconect the flat ribbon cable by aligning and carefully pushing into the conector on the main circuit board.
14. Plug in power source,and turn on power.
15. When printer boots up, answer the questions on the printer screen for your area.
16. The printer will cycle the ink from the cartridges to the print head and back.

Pineworks

it wont ever work.this is a nortel proprietary telephone and will only work on the nortel products. there is also issues with voltages etc.you are lucky if you have not damaged the ptt end of your home line remove it as quickly as you can...hope this helps

Its not the battery, its AC power source providing your problem.
Check if AC connector goes in as far as it should on your laptop, check so you dont have a weak link on the cables on the AC. My guess is that the power sorce or the cables on is defect someway.

Good luck!