Question about Acme 5001 Supreme Juicerator Juice Extractor

1 Answer

Screw that holds down the blade in cwnter

Hey I might need a new screw that holds down the round blade in the center. think we lost it......where can I get one

Posted by on

  • 4 more comments 
  • flood Dec 14, 2007

    need hold down screw to keep round blade in place

  • Anonymous Dec 20, 2007

    Hello.



    I lost the that screw too and need another. Where can we find it?

    please help



    darlenedeloney@yahoo.com

  • Anonymous Feb 12, 2008




    necesito tornillo que sujeta la hoja


  • Anonymous Feb 27, 2008

    screw for acme juicer

  • powerdad1000 Oct 25, 2008

    I need the screw and a new blade. Why is it so hard to get parts?

  • vrivers56 Nov 26, 2008

    I NEED A SCREW THAT HOLDS THE BLADE IN THE MIDDLE IN PLACE

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Try here, not sure if it's listed or not though: http://www.healthnutalternatives.com/acme5001.htm

Posted on Sep 19, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My lid doesn't seem to fit properly. When I put the top on to cover the screen, it doesn't seem to fit together properly-- the bottom of the chute that you throw the fruit and veggies down butts right up...


Is this a new cover? There is an adjustment. On the bottom of the machine, dead center,
there is an adjustment screw with a locking nut. Unlock the nut and the turn the screw
counter clockwise, this will lower the motor shaft and consequently the blade. Once you
have clearance and install the cover, turn the screw clockwise until the blade contacts the
chute, back it off a half turn and lock her down. This will establish the correct gap between
the chute and blade. Also if your chute is ever chipped or scored by the blade because
of excessive vibration, you can file the chute level and readjust the gap.

Mar 13, 2011 | Omega 1000 Juice Extractor

1 Answer

Just received replacement Latch arm for Omega 1000. Old one is removed. Can not put the new one. Top part does not slide in. Also noted the old part and new part look different. Base is longer in the...


Believe it can be done. You might have to file or shave the new arm a little then seat it as best
as possible and tap it in place with a screw driver and hammer. If you do manage to attach
the new arm and the fit is a little too snug when you latch down the cover, file the upper tip
of the arm for a little more tolerance. Also, believe it or not, a worn blade will produce less
vibration. There is a set screw bottom center. With the juicer fully assembled, unlock it,
turn it clockwise until feed chute contacts the shredder blade and back it off a half turn.
You now have the proper gap between the chute and blade.

Jan 30, 2011 | Omega 1000 Juice Extractor

1 Answer

When we juice, it turns and moves across the counter


Both the Omega and Acme juicers vibrate no matter what you do. I found a worn shredder
blade actually produces less vibration. However this involves filing the cutting burrs down
and resetting the blade to chute gap. If you're up to it, take the blade out and file each row
of burrs about halfway down. Then with the juicer fully assembled, unlock the set screw on
the center of the bottom, turn it clockwise until the chute contacts the blade, and back it off
a half turn. The set screw actually raises and lowers the motor spindle. Both companies
would not agree with this, but this solution comes from operating my 21 year old Acme.
I recently replaced the blade and the juicer immediately began tap dancing. Went back to
the old blade.

Jan 16, 2011 | Omega 1000 Juice Extractor

1 Answer

Excessive vibration and rattling when I have less than a cup of juice extracted.


I've had an Acme for 21 years and I don't care
what anyone tells you-they vibrate. After years
of trial and error I found mine vibrates less with
a worn blade that I sharpen with a drill. With
a new shredder blade you actually have to file
down the cutting burrs about one third and
adjust the blade to chute gap by unlocking
the adjusting screw on the center of the bottom,
turn it clockwise until blade contacts chute, and
back it off a half turn. Apparently with a slightly
duller blade, smaller gap, the produce goes through
more slowly and evenly. Also severe vibration will
cause the blade to jump up and chip the chute.

Dec 24, 2010 | Acme 5001 Supreme Juicerator Juice...

1 Answer

Acme juicer vibrating so much.


I've had one for 21 years and when I replaced the blade the same thing happened.
The blade is not supposed to be held firmly in place so it can slip intentionally to
minimize vibration. If you bought the juicer new, think back, and I believe you will
remember the vibration problem. I seems with a worn blade they vibrate less. The
motor is very durable and uses roller bearings like on a skate board. I went back
to the old blade, which I sharpen with a drill using a small bit.

Jan 11, 2010 | Acme 6001 Juice Extractor

1 Answer

How does it come apart for cleaning


The hot water did work for mine. Here is the solution I discovered:

After removing the food plunger and juicer cover: (1) Unscrew the 3 screws that hold the cutting blade plate in the center of the basket and lift off the cutting blade plate; (2) Unscrew the base counterclockwise (it will unscrew from the threaded center piece) and lift it up; (3) Lift off the basket and juice bowl. Now you can clean the basket and juice bowl.

To reassemble, reverse the process.

Sep 20, 2009 | Juicers

1 Answer

I HAVE A JUICER MODEL #JE95XL ITS ONE YEAR OLD,I


Go to Lowes, to the cabinet knob dept. Get a cabinet knob that matchs the holes in blade. You can always bend the screw a tiny bit if needed to fit. Put the screws into cabinet knob, and tighten. Cut the heads off and you are ready to go. They have a knob that is stainless steel, just a flat piece across the top, an 2 straight pieces that go down. I think it was $2.97. It gives good grip, and takes the blade right off.

Aug 21, 2009 | Breville JE95XL Juicer

2 Answers

Acme juicer #6001, has a new blade, becomes unbalanced...


Hello, First, make sure the screw on clamp that holds the blade down is centering the blade correctly. Also make sure it tightens down firmly against the blade. Wiggle the blade to ensure it is mounted securely. If this doesn' fix it try your old blade again. If your old blade works you may have a bad, unbalance blade but I would suspect he screw on clamp knob may be somewhat worn and not securing the blade causing it to run "out of round" when a piece of vegetable pushes on it. If everything looks good with both blades and the blade securing knob it could be a worn bearing on the juicer. Try wiggling the motor shaft and see if there is any play in it. I have an ACME 6001 that is quite old so I wouldn't suspect the bearings are going. One other thing, does the bowl take 3 to 5 minutes to stop spinning when you shut off the motor? If it does then the shaft and bearing are probalby ok

Good luck with it...gary

Jan 05, 2009 | Acme 6001 Juice Extractor

4 Answers

How to dissassemble Jack Lalanne Power Juicer?


After about a half hour I finally figured it out. I'll go through all the steps.

1. Remove pusher from chute.
2. Pull the locking bar down over the spout.
3. Remove lid.
4. This part is tricky. Stick the orange crescent tool into the blade holes and while holding the filter basket steady with one hand, turn the blade couterclockwise while pulling up.You do have put a little muscle into it. And remember, if you don't hold the filter steady, the whole damn thing just spins.
5. Remove the receptacle.

Good juicer, but it seems unnecessarily complicated.

Jan 01, 2008 | Jack Lalanne Power Juicer 250 Watts

Not finding what you are looking for?
Acme 5001 Supreme Juicerator Juice Extractor Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acme Juicers Experts

yadayada
yadayada

Level 3 Expert

78257 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

19004 Answers

Are you an Acme Juicer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...