Scooter motor does not operate

2 Beeps -Motor disconnected
The motor has a bad connection. Check all the connections and leads between the motor and S-Drive. Check the position of the freewheel lever.

9 Beeps - Solenoid brake trip
The parking brakes have a bad connection. Check the parking brake and motor connections. Make sure all the system connections are secure.

When in doubt, read the manual :>D

https://www.manualslib.com/manual/165351/Sterling-Mobility-Scooter.html?page=36

..

Hi it's possible the computer (control box) shut down remove key for a short time then try to start scooter .., Cheers

hi Graham, okay assuming it got a PG Drive controller or a ds 90 dynamic controller fitted , 9 flashes means a internal fault ,,,check all of the connections to the controller including the brake and motor connection.. it 's can be a real frustrating fault..For example i had scooters working perfectly then one day 9 bleeps, after making sure of connections were good ,it worked once again..

Currently i 'm working on a ds 90 dynamic controller , it got a 9 bleep problem, dry joints on the controller board ...

Regards
Rob...

The manual for this scooter is at http://www.discovermymobility.com/store/scooters/summit-scooters/elite-portable-scooter/manual.pdf
The closest info I can find is page 14. MOVING AND TRANSPORTING YOUR Easy Travel Elite
6.1. Moving Your Easy Travel Elite in Freewheel Mode when unfolded:
The Freewheel switch (Fig. 1/17) is used for releasing the brake and moving the Easy Travel Elite without operating the motor. Before activating, make sure your Easy Travel Elite is switched on. Turn Freewheel switch to the "freewheel" position and push or pull the Easy Travel Elite manually.
NOTE: The Freewheel mode can only be activated after the battery is in place and the power switch (Fig.9/1) is turned on. Doing otherwise will cause a fault situation indicated by rapid flashing of the Indicator light (Fig. 9/4). See section 4.2.
WARNING: The Freewheel switch should never be engaged on a slope.
CAUTION: The seat back must remain in the upright position.

They seem to assume removal is obvious, I would check any connections from battery to scooter are pulled out and that freewheel mode is not engaged.

Hi 9 beeps .is a solenoid brake trip fault ( CHECK PARKING BRAKE for BAD connections on motor & check all wiring connections.cheers

please can you tell me how ofter the light's flash ? does there appear to be some kind of sequence ?

Hi, I take it been taken then, do you get a error codes ?

see below


DIAGNOSTIC FLASH CODES
The diagnostic flash codes for your scooter are designed to help you perform basic troubleshooting quickly and
easily. A diagnostic flash code will flash from the status LED in the event one of the conditions listed below
develops.
NOTE: Your scooter will not run unless the flash code condition is resolved and the scooter has been
turned off, then turned back on.
Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that
may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because
the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.
FLASH CODE CONDITION SOLUTION
! (1) Battery charge is low. Charge batteries as soon as possible.
! ! (2)
Batteries are too low to operate the
scooter.
Charge batteries.
! ! ! (3)
The scooter’s battery voltage is too
high to operate the scooter, or the
charger is still connected to charger
port.
Unplug charger and/or turn key off, then
back on again.
! ! ! ! (4) Current limit time out.
Turn the scooter off for a few minutes,
then turn your scooter back on.
! ! ! ! ! (5)
The manual freewheel lever is in the
(forward) freewheel position.
Remove the key from the key switch,
then push the manual freewheel lever to
the (rear) drive position, and restart your
scooter.
! ! ! ! ! ! (6)
Throttle control lever not at center
position at start up.
Return the throttle control lever to center
position, turn scooter off, then back on.
! ! ! ! ! ! ! (7) Speed pot error.
Contact your authorised Pride Dealer for
assistance.
! ! ! ! ! ! ! ! (8) Motor volts error.
Contact your authorised Pride Dealer for
assistance.
! ! ! ! ! ! ! ! ! (9) Other internal errors.
Contact your authorised Pride Dealer for


Regards
GeWiz.

It sounds like it could be locked. Try pressing and holding the power button until it bleeps. then move the joystick to the forward position and hold until it bleeps. Then move the joystick to the reverse position until it bleeps. turn off and then back on.

Check your manual for locking/unlocking. Hope it works

On 2002 model try the following:
1. Close all vehicle doors.

2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.
4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).
6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.
10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.
11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).
12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.

from ProgramyourRemote