Question about Maytag Performa PAV2200

1 Answer

HELP!!!!!! WE ARE TRYING VERY HARD TO FIND OUT JUST HOW TO TAKE THE WASHER A PART TO TRY AND FIGURE OUT THE PROBLEM. THE WASHER IS NOT SPINNING OUT THE WATER.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Before spinning, washer draining water aut & than start spinning,,,,if motor runing without drainig water, chek the belt, if belt is OK,and runing pupm, chek the pump,,,,disconnect hoses and clean pump... if washer do not draining & spinning, replase lid switch..... If you need instruction how to replace lid switch, i will post you instruktion....

Posted on Sep 02, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring of Fisher Paykel pump


The Green wire goes on the side of the pump.
Here is a picture

59a5a467-b194-495a-9b9e-3985ead4c7fa.jpg

May 25, 2012 | Fisher and Paykel Fisher Paykel Intuitive...

1 Answer

My washing is still soppy wet, won't spin, won't work only makes a humming sound. I cleaned out the hoses, drain pipes etc but still not working. How do i reset the machine.


Humming means ur motor is trying hard to start spinning! Either ur CAPACiTOR is not good anymore or the washtub is stuck( something kept it from spinning, might be a clothe stuck under the the barrel washer)!
Try to check on those parts!

Nov 21, 2010 | Washing Machines

1 Answer

Whirlpool Duet makes spinning sound but drum is not spinning.


What is the model number? To get your clothes out and the door open on that model, try unplugging it for awhile and open the door (you probably have tried that already. Some models you can take off the bottom panel and reach up and there is a little ring you can pull to open the door. (most likely) you might be hearing the pump running since it always run when spinning. If you give me the model number I can let you have the test code. You could try Pressing any key (not power or stop) hold it in for 3 seconds let go 3 seconds, press 3 sec, let go 3 sec, hold 3 sec let go. It should come up all lights on. Don't worry you can't damage anything in the test mode. Watch what it says. then press that same key about every 30 seconds to advance it. It's kind of hard to explain but I'm trying my best. It should at least unlock it in the process. Good luck

Jan 24, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

I have a top load Kenmore washer, it is not spinning out and the drum is moving back and forth,


This is a bad motor position sensor. Since the machine cannot tell what position the motor is in it just spins back and forth trying to figure it out. Often an error code will pop up after 15-20 minutes.

A technician should be able to replace this part relatively cheaply. Hope this helps, please rate my solution.

Jan 01, 2009 | LG WM-2077C Front Load Washer

1 Answer

Trying to fix belt


this machine does not have a belt, sounds like your coupling is broken.it will still drain with a broken coupling.

Oct 13, 2008 | Whirlpool LSR5132PQ Top Load Washer

1 Answer

WHDSR209D Washer


if you have a rubber smell that means that the belt is burning through. Several problems can be the case.
1 bearing of the drum ( check if it turns freely if so the bearing is ok)\
2 the belt is worn and need to be replaced.
3 carbon brushes in motor are worn
4 bearing in motor is gone

open the backside of the machine and check belt.
think that is your problem

Apr 30, 2008 | GE WBSE2090A Top Load Washer

1 Answer

Water drains, but washer does not spin


try opening the filter which located mostly in the lower area of the front side. An acumilation of dirt and calc will inhibit the complete drain of water. After opening and cleaning the filter, put it back in. Once it will drain completly, it will start spinning. Hope I assist you with the problem.

Nov 18, 2007 | GE Energy Star WCVH6260F Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

588 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...