Question about Washing Machines

1 Answer

G e washer fills slow on 2nd rinse

Model #wcse3100a1ww fills very slowly on 2nd rinse. i have cleaned all filters and replaced valve assembly. is the control asembly now the problem? how can i test it i

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 291 Answers

Check volts at water valve in first rinse ..note that ... when in 2ed rinse check volts to w. valve and see if theres any difference in volts to valve... also compare the water pressure coming in washer ... how much pressure difference.. lot, little ? generally water valves work or dont work in all cycles ,,,this a new one for me post your results

Posted on Sep 02, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool awm 1200/1


check the pump to see if anything is clogged in there or you could have a bad pump,open the door and look around the opening and you'll see the full model number.also if it stops at the rinse cycle does it fill with water and the water is in there but doesn't drain or are the clothes just sitting there wet,because when in rinse the machine just uses cold water and if the valve is clogged or filling slowly the washer will stop after like 6 minutes,does any error codes come up?you can try to start the washer just on cold water and see if the water fills slowly or if it comes in normally,if it comes in slow most likely that will be your problem,if it is the pump you can get a shop vac and suck out the water from the drain hose,get it as close to the floor as you can and it will work better,then remove the center part of the pump,the clean out and see if it's filled with stuff,turn it slowly,when water comes out vac it up with shop vac until it stops.hope this helps you out.

Feb 10, 2018 | Washing Machines

1 Answer

Water comes out wash cycle good but slow at rinse cycle


do you mean filling the washer up or draining it out?i think you mean filling it up,on washers just the cold water is used to fill the washer on the rinse cycle,you can shut the water down and remove the cold water line and see if you can clean out the screen in the washer water valve,also while you have the hose off,stick it in the washer and open the valve to see how the pressure is,if it's coming out strong then the problem is in the washer and you should change the washer water valve,if it's coming out slowly then you have a problwm with the house water valve and need to change that out.let me know what you find

Aug 29, 2010 | Whirlpool LTE5243D Top Load Stacked...

1 Answer

I have the LG WM1832cw washer. Something is wrong with the cold water fill. Not the hot water just the cold water fill valve section as it fills VERY VERY SLOW (water trickels in). Hot water fills fast! I...


Is resistance between each terminal of INLET
VALVE ASSEMBLY 0.8~1.2 kω? If not replace it.
Is the inlet valve filter clogged?
Clean the filter.
Verify the voltage of the inlet valve connector is
120 V AC. No voltage? Check electrical connection.
Replace the MAIN PWB ASSEMBLY.
I have an LG training manual which might not be the exact one you need but it gives an idea what to look for.

LG WASHER REPAIR MANUAL

Post your model number at any of these
fine forums for an answer
that will save you big money::
http://appliancejunk.com/forums/index.php?referredby=858
http://forum.appliancepartspros.com/
http://applianceguru.com/
NEW! http://sublimeforum.invisionplus.net/


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Nov 10, 2009 | Washing Machines

1 Answer

Slow Cold Water Fill


There is possibly a filter screen in the hoses as well as the water valve.Check the hoses for screens.Occasionally the water valve will deteriorate inside and must be replaced.
I am on a water well and have the same problem. This weekend I installed a inline filter purchased from Lowes. It has stopped the sand and silt problem. You will have to buy one extra water hose to do this yourself.

Jul 16, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Kenmore 90 Series fills so slow on rinse cycle


For low water volume - or "Trickling" effect...

1. Turn off the water supply to both hoses.
2. Remove hoses (one at a time so you don't get them confused)
3. On the washer side - look for a removeable screen inside where you just removed the hose.
4. Using a small screwdriver - pop out the screen and reverse-flush it/clean it. It will likely be full of sediment and calcium deposits from your pipes.
5. Replace the inlet screens.
6. Re-fit the hose to the machine.
7. Turn on water supply valves.
8. re-try.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Feb 09, 2009 | Kenmore 15944 Top Load Washer

1 Answer

Washer fills slow only in the rinse cycle


Need a model # to get exact part you will need at rinse most washer go straight cold so I would say water inlet valve if humming sound is present

Apr 28, 2017 | GE WBSR3140DW Top Load Washer

1 Answer

Washer fills slow only in the rinse cycle


ck and clean screens first both sides be sure hoses are not reversed timer has no affect on fill rate if screens are clean replace valve

Sep 19, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Ge profile whsb8000bocc


Washer is most likely trying to fill with cold rinse water and the inlet screen is blocked or the cold water solenoid is bad. If you set washer to wash cold only it will not fill or fill very slowly. When you set it to warm or hot you are getting almost all hot. Clean inlet screen or replace inlet water valve.

May 12, 2008 | GE Profile WPSR3120WWW

1 Answer

Slow Filling only in rinse cycle


Tony, the fact that you are not receiving any error codes tends to leave me to believe that your cold fill hose filter may be restricted. Going by your model number you can enter this mode by having the power on at the source and off at the console. Press and hold the lifecyle button and then push power button. You should hear 2 beeps and then the display go blank. You can test the hot and cold valves by pressing how dirty up (hot) and how dirty down (cold). If you find the cold valve slow as in your rinse check for restrictions. If it were the thermistor, I would think you would receive an error code..Good luck.

Jun 06, 2006 | Fisher and Paykel IWL12 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

325 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85160 Answers

Brad Brown

Level 3 Expert

18072 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...