Question about Canon F-710 Calculator

Here try this manual:

http://www.arrl.org/files/file/Instructor%20resources/Herber%20W9HE/notes2012.pdf

Posted on Aug 01, 2013

Hi,

a 6ya expert can help you resolve that issue over the phone in a minute or two.

best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).

click here to download the app (for users in the US for now) and get all the help you need.

goodluck!

Posted on Jan 02, 2017

If you mean it is not showing everything after the decimal point, you can change that by pressing the [f] key followed by the number of decimal places to display. For example, to restrict it to 2 places, press [f][2]. If you want to see 4 places, press [f][4].

To show all possible decimal places, use the sequence [f][9].

From the manual (http://www.hp.com/ctg/Manual/c00363319.pdf):

"To display a different number of decimal places, press f followed by a digit key (0 through 9) specifying the number of decimal places. In the following examples, notice how the displayed form of the number inside the calculator - 14.87456320 - is rounded to the specified number of digits."

"Although nine decimal places were

specified after f, only eight are

displayed since the display can

show a total of only 10 digits. "

The standard display format, plus the specified number of decimal places, remain in effect until you change them; they are not reset each time the calculator is turned on. However, if Continuous Memory is reset, when the calculator is next turned on numbers will be displayed in the standard display format with two decimal places

shown.

If a calculated answer is either too small or too large to be displayed in the standard display format, the display format automatically switches to scientific notation. The display returns to the standard display format for all numbers that can be displayed in that format.

http://www.hp.com/ctg/Manual/c00363319.pdf

To show all possible decimal places, use the sequence [f][9].

From the manual (http://www.hp.com/ctg/Manual/c00363319.pdf):

"To display a different number of decimal places, press f followed by a digit key (0 through 9) specifying the number of decimal places. In the following examples, notice how the displayed form of the number inside the calculator - 14.87456320 - is rounded to the specified number of digits."

"Although nine decimal places were

specified after f, only eight are

displayed since the display can

show a total of only 10 digits. "

The standard display format, plus the specified number of decimal places, remain in effect until you change them; they are not reset each time the calculator is turned on. However, if Continuous Memory is reset, when the calculator is next turned on numbers will be displayed in the standard display format with two decimal places

shown.

If a calculated answer is either too small or too large to be displayed in the standard display format, the display format automatically switches to scientific notation. The display returns to the standard display format for all numbers that can be displayed in that format.

http://www.hp.com/ctg/Manual/c00363319.pdf

Sep 12, 2014 | HP 12c Calculator

There is only one key to toggle between display formats: the S<>D key. Pressing the key repeatedly will cycle through all available display formats.

May 23, 2012 | Casio FX300WPlus Scientific Calculator

You're in BASE-N mode for integer arithmetic. Press MODE 1 to get to COMP mode for real arithmetic or MODE 2 for CMPLX mode for complex arithmetic.

Apr 04, 2011 | Casio FX-115ES Scientific Calculator

If you're dealing with complex numbers, the arithmetic doesn't matter what display mode you're in. Just enter the number and do the math. To switch the display mode, press SHIFT MODE down 3 to select CMPLX, then make your choice.

Oct 07, 2010 | Casio FX-115ES Scientific Calculator

I am not sure what you want because the mathIO mode IS THE ONE THAT DISPLAYS results as fractions.

You have two display modes: MthIO (with fractions, radicals) and LineIO (with decimals). Which one do you want?

To set MthIO press [Shift][MODE][1:MthIO]

To set LineIO, press [SHIFT][MODE][2:LineIO]

Concerning the scientific display mode.

Decimal numbers can be displayed in various formats, Fixed,Scientific, and Normal. If you do not want scientific display of results, just set the mode to Fix(ed) and specify the number of decimal digits. However if a number to be displayed (a result) is too small or too large IT WILL BE DISPLAYED in scientific format regardless of the mode you selected.

You have two display modes: MthIO (with fractions, radicals) and LineIO (with decimals). Which one do you want?

To set MthIO press [Shift][MODE][1:MthIO]

To set LineIO, press [SHIFT][MODE][2:LineIO]

Concerning the scientific display mode.

Decimal numbers can be displayed in various formats, Fixed,Scientific, and Normal. If you do not want scientific display of results, just set the mode to Fix(ed) and specify the number of decimal digits. However if a number to be displayed (a result) is too small or too large IT WILL BE DISPLAYED in scientific format regardless of the mode you selected.

May 13, 2010 | Casio FX-115ES Scientific Calculator

Hi,

**It is still a great calculator and what it is doing now is not the result of a defect. **Rather, it** **is a configuration setting that someone has activated.

The calculator has three display modes for the numbers.

Standard 'normal', scientific and engineering. The calculator respects the user's choice as long as possible, but if the numbers are too small or two large it uses the scientific display format.

To set the 'normal' display format:

The calculator has three display modes for the numbers.

Standard 'normal', scientific and engineering. The calculator respects the user's choice as long as possible, but if the numbers are too small or two large it uses the scientific display format.

To set the 'normal' display format:

- Press [2nd][MODE]. On first line of screen that is displayed, make sure that Normal is highlighted. If it si not, use the arrow to move cursor on it and press [ENTER].
- Use arrow to move cursor to 2nd line. Highlight the number of decimal digits you want (0, 1, 2, ...,or 9) and press ENTER.
- Quit the MODE setting. From now on the calculator will use the 'normal' display format with the number of decimal digits you chose, until you change this setting again.
- However if the number displayed is too small or too large it will be display it in scientific exponential notation. Subsequent numbers that are not too small nor too large will obey the 'normal' format.

Nov 12, 2009 | Texas Instruments TI-86 Calculator

Hi,

The number displayed is 3.006 x10^12 or 3 006 000 000 000. It requires 13 digits to dsiplay but the calculator does not have that may places, so it reverts to scientific notation**even if the mode is et to 'standard'.** If numbers are too small or too large the calculator uses scientific notation **regardless **of the display format the calculator is configured for.

Hope it helps

The number displayed is 3.006 x10^12 or 3 006 000 000 000. It requires 13 digits to dsiplay but the calculator does not have that may places, so it reverts to scientific notation

Hope it helps

Nov 10, 2009 | Texas Instruments TI-30XA Calculator

The [MODE] key can be used to select the modes described below.

Important! The following is a general explanation of Scientific Calculator modes. Note that your calculator may not include all of the modes described here.

1) Calculation Modes

Before performing a calculation, you first need to select the appropriate calculation mode.

COMP: Basic arithmetric calculations

(arithmetic operations, trigonometric functions, etc.)

COMPLEX: Complex number calculations

SD: Single-variable statistical calculations

(sample standard deviation, etc.)

LR or REG: Paired-variable statistical calculations

(linear regression statistical calculations, etc.)

BASE or BASE-n: Binary, octal, decimal, hexadecimal number system calculations

MAT: Matrix calculations (determinants, etc.)

VCT: Vector calculations

EQU: nth degree equations, simultaneous equations

2) Display Settings

Use these settings to control how calculation results are displayed.

Note that changing the Fix and Sci settings does not affect internal calculation results.

Norm: Exponential display format and cancels the currently configured Fix and Sci settings.

Fix: Specifies a fixed number of digits to the right of the decimal place.

Sci: Specifies a fixed number of significant digits.

3) Angle Unit Setting

(90°=?/2 radians=100 grads)

Deg: Degrees

Rad: Radians

Gra: Grads

4) Engineering Mode

Use this mode when you want to input and perform calculations using engineering symbols.

Please rate this response . .

Important! The following is a general explanation of Scientific Calculator modes. Note that your calculator may not include all of the modes described here.

1) Calculation Modes

Before performing a calculation, you first need to select the appropriate calculation mode.

COMP: Basic arithmetric calculations

(arithmetic operations, trigonometric functions, etc.)

COMPLEX: Complex number calculations

SD: Single-variable statistical calculations

(sample standard deviation, etc.)

LR or REG: Paired-variable statistical calculations

(linear regression statistical calculations, etc.)

BASE or BASE-n: Binary, octal, decimal, hexadecimal number system calculations

MAT: Matrix calculations (determinants, etc.)

VCT: Vector calculations

EQU: nth degree equations, simultaneous equations

2) Display Settings

Use these settings to control how calculation results are displayed.

Note that changing the Fix and Sci settings does not affect internal calculation results.

Norm: Exponential display format and cancels the currently configured Fix and Sci settings.

Fix: Specifies a fixed number of digits to the right of the decimal place.

Sci: Specifies a fixed number of significant digits.

3) Angle Unit Setting

(90°=?/2 radians=100 grads)

Deg: Degrees

Rad: Radians

Gra: Grads

4) Engineering Mode

Use this mode when you want to input and perform calculations using engineering symbols.

Please rate this response . .

Sep 08, 2009 | Casio MS-80TV Scientific Calculator

Check this HP FAQ:

Setting a Fixed Decimal Place You can download the manual and user guides for your calculator from here:

http://h10025.www1.hp.com/ewfrf/wc/manualCategory?lc=en&dlc=en&cc=us&product=81575&lang=en&

For more information, Faqs & how-Tosgo the HP support homepage for your calculator:

http://h10025.www1.hp.com/ewfrf/wc/product?lc=en&dlc=en&cc=us&lang=en&product=81575&

Introduction This document describes how to set the desired number of decimal places on the HP 12c calculator in standard format. It also covers how to enter a number in scientific notation. Instructions for standard format

Introduction This document describes how to set the desired number of decimal places on the HP 12c calculator in standard format. It also covers how to enter a number in scientific notation. Instructions for standard format

Setting a Fixed Decimal Place You can download the manual and user guides for your calculator from here:

http://h10025.www1.hp.com/ewfrf/wc/manualCategory?lc=en&dlc=en&cc=us&product=81575&lang=en&

For more information, Faqs & how-Tosgo the HP support homepage for your calculator:

http://h10025.www1.hp.com/ewfrf/wc/product?lc=en&dlc=en&cc=us&lang=en&product=81575&

Introduction This document describes how to set the desired number of decimal places on the HP 12c calculator in standard format. It also covers how to enter a number in scientific notation. Instructions for standard format

- Press and release .
- Press the number key for the desired number of decimal places to be displayed to the right of the decimal point (0 through 9). The calculator displays a maximum of 10 digits.

Introduction This document describes how to set the desired number of decimal places on the HP 12c calculator in standard format. It also covers how to enter a number in scientific notation. Instructions for standard format

- Press and release .
- Press the number key for the desired number of decimal places to be displayed to the right of the decimal point (0 through 9). The calculator displays a maximum of 10 digits.

Aug 24, 2009 | HP 12c Calculator

There is a button there that says "S<=>D". Compute it first and when the result is in fraction, press this and it will be in decimals. This button is just above the DEL button.

May 12, 2009 | Casio FX-115ES Scientific Calculator

Nov 28, 2012 | Canon F-710 Calculator

Dec 20, 2011 | Canon F-710 Calculator

73 people viewed this question

Usually answered in minutes!

×