Question about Jenn-Air 24 in. JDB1250 Built-in Dishwasher

1 Answer

Start button does not light

The start button does not light up and start the process . all other button turn on

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jenn-Air Master
  • 12,223 Answers

Please follow this steps and fix it. GOD BLESS YOU

1. No power to the dishwasher
Make sure there's power getting to the dishwasher. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power. Sometimes the power cord disconnects at the dishwasher (inside the junction box, behind the bottom kick panel), if this is the case, the wiring must be repaired or replaced.

2. Door switch
Replace if defective.

3. Timer or Electronic control
Replace if defective (note: uncommon problem).

4. Selector switch
Replace if defective (note: uncommon problem).
Read more: http://www.appliancepartspros.com/repair-help/dishwasher-repair-help.html#ixzz2aaj83j00
http://www.appliancepartspros.com

Posted on Jul 31, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cannot connect to network. It show IP address 0.0.0.0


contact your service provide for assistance on how to set it up

Apr 28, 2015 | HP LaserJet P2015n Printer

1 Answer

My pc loses video while booting, and frizes, I still see the start button light on


There could be many reasons...
From hardisk failure ...to virus
Try to get in the Bios setup while PC is bootin and load default Bios settings.Save and exit.
Just as first step.

Jul 10, 2012 | Gateway Computers & Internet

2 Answers

Cant calibrate tony hawk shred board to my wii. I've tried everything


At last! My Son's Tony Hawk Shred board was one more try from being thown down the garden, as i have been trying since Christmas day, & finally there it was a board i could use. I've followed all bits of advice in a number of differant ways --- here's what worked for me, Turn off at the wall Sky TV, Turn off all lights (only tv turned on), put my crutches in another room (because large metal objects interfere with soft ware), Remove dog from room, Put senser bar on floor, Turn Wii console side on so that Dongle faced away from tv (aiming into centre of room), Place Shred board on floor facing tv/senser at about three feet away. Start process of game set up untill you get to choose a profile, Select profile, press & hold for 5 secs start button on board untill the four blue lights start to flash at a rate of about one flash per sec, then hold on same button untill blue lights flash quickly, then press & hold Dongle button untill Dongle light stays on, with in 2 secs game calibartion instructions start, BEWARE Tony Hawks responce when process starts is as annoying as not being able to get board started. Good luck when up & running it is one Awesome game!

Jan 01, 2011 | Activision Tony Hawk Ride for Nintendo Wii

1 Answer

I have a motorola blue tooth and I need to pair it to my htc evo.... How can I do that?


Ok, I'll give you a default procedure to put a blueetooth headset in pairing mode: starting with it turned off, press and hold the call button as if you were turning it on, but keep pressing the button until the indicator light is either steadily lit, or flashing rapidly, sometime in more than one color. This is usually achieved by holding the button down for some 6 to 10 seconds. Then, make your phone's blueetooth application search for new devices. After a while, your headset should appear on-screen. Make the application connect to it. If a pairing code (or passkey, or PIN), is requested, enter '0000' (four zeros). If the pairing process is successful, your headset's indicator light should flash some times, and enter the stand-by mode (normally flashing every couple of seconds). Your phone should also indicate that a headset is connected. However if the pairing process fails, after a couple of minutes your headset will quit the pairing mode, Turn it off, by pressing the button until the light goes off, and start the whole process again, firstly trying '0000' one more time, then changing it either by '1234' or '8888',
Hope you are able to sort your problems out soon, but, please, let me know if you further assistance.
Regards, Carlos

Sep 14, 2010 | Motorola Mobility Bluetooth Hands Free...

1 Answer

Unable to print a configuration page for hp jaserjet p2015 Series printer


Try this:
To print a Configuration page, press and hold the Go button for 5 seconds. When the Attention lights in on, relase the Go button (The printer is ready with no job activity)

To print a Demo page, press and release the Go button.

If the printer has a network card and the page is not come out, then is possible to view config page in web browser by typing printer IP address. Sometimes an administrator ID and Password should be necessary.
A cold reset should be resolved this issue.
steps for cold reset
---------------------
a)Turn off the printer.

b)Press and hold the Go button.

c)Turn the printer on, and continue to hold the Go button for at least 5 seconds, but not longer than 15 seconds. During this process, the Attention LED turns on.

d)Release the Go button.

NOTE: If both the Attention and the Ready LEDs turn on before you release the Go button, you must start the procedure again with step 1.Even if any other lights come before the attention light re-do the process.If at second attempt the same thing happens then there is nothing that can be done you will need to contact HP for tech help.

Attention !!!!! The Cold reset erase network card
configuration

Sep 22, 2009 | HP Office Equipment & Supplies

1 Answer

WHEN I TURN ON THE PRINTER IT STARTS TO PRINT THE ALIGNMENT PAGE


Hi Mahdavi,

In HP PSC 1315 printer after replacing new Ink Cartridges the printer always prints Alignment test page every time you turn it ON.To resolve this problem you must complete the alignment process.

Steps

1.Turn the printer ON.
2.Once its ON, it will print the Alignment page. Place the page in the scanner bed correctly.
3.Then Press START SCAN button.
4.The power light will start blinking, wait until the power lights turns solid.
5.Now Alignment process is over.Discard the paper from scanner.
6.Turn the printer OFF and then ON, it will not print that page again.

Note:Please follow this steps every time when you replace the Cartridges.

Thanks
Rizwan
rizwan84tx@gmail.com

Dec 06, 2008 | HP PSC 1315 All-In-One InkJet Printer

1 Answer

Laserjet 2015n powers up for 2-3 seconds - but no lights come on - and then it powers down.


Hello,

Please perform the following.

Super NVRAM initialization Turn off the printer.
  1. Press and hold the Go button.
  2. Turn on the printer and continue to hold the Go button for at least 50 seconds. During this process, the Attention , Ready , Go lights turn on. Then the Attention and Ready lights turn off, leaving only the Go light illuminated.
  3. Release the Go button. The Go , Ready and Attention lights turn on.
  4. Press and hold the Go button. All lights turn off. During the next three seconds, the Go , Ready and Attention lights turn on in that order, one per second.
  5. Release the Go button to perform the initialization. The control panel lights begin cycling from front to back. After the Super NVRAM initialization process is complete, the printer returns to the ready state.

Sep 19, 2008 | HP LaserJet P2015dn Printer

1 Answer

2015 network printer


Hello,

Please perform the following:

Unplug the network Cable:

Cold reset A cold reset changes most system parameters in NVRAM to the factory defaults. However, unlike NVRAM initialization, a cold reset does not reset the page count, the paper tray sizes, language, or formatter number.
A cold reset also resets all the HP Jetdirect settings as well as the printer settings. Use the following procedure to perform a cold reset.
  1. Turn off the printer.
  2. Press and hold the Go button.
  3. Turn the printer on, and continue to hold the Go button for at least 5 seconds, but not longer than 15 seconds. During this process, the Attention LED turns on.
  4. Release the Go button.
    If both the Attention and the Ready LEDs turn on before you release the Go button, you must start the procedure again with step 1.
The printer's LEDs begin cycling. The cold-reset process runs until completion, and the printer returns to the ready state.


Network reset A network reset changes all network system parameters in NVRAM to the factory defaults. During the network-reset process, all button presses are ignored.
Use the following procedure to perform a network reset.
  1. Turn off the printer.
  2. Simultaneously Press and hold the Go and Job Cancel buttons.
  3. Turn on the printer and continue to hold the Go and Job Cancel buttons for approximately 10 seconds, but no longer than 20 seconds. During this process, the Attention light turns on.
  4. Release the Go and Job Cancel buttons. The Attention , Ready , and Go lights begin cycling from front to back. After the network-reset process is complete, the device returns to the ready state.
    If the Attention and Ready lights illuminate before you release the Job Cancel button, start again at step 1.
Now plug in the network cable and then wait for 5 mins.
Then print a configuration page and check the IP Address.

Jul 29, 2008 | HP LaserJet P2015dn Printer

1 Answer

Metwork card


Hello,

Your printer is a dn model, which means it is duplex + network. Please unplug the network cable and perform the following:

Cold reset A cold reset changes most system parameters in NVRAM to the factory defaults. However, unlike NVRAM initialization, a cold reset does not reset the page count, the paper tray sizes, language, or formatter number.
A cold reset also resets all the HP Jetdirect settings as well as the printer settings. Use the following procedure to perform a cold reset.
  1. Turn off the printer.
  2. Press and hold the Go button.
  3. Turn the printer on, and continue to hold the Go button for at least 5 seconds, but not longer than 15 seconds. During this process, the Attention LED turns on.
  4. Release the Go button.
    If both the Attention and the Ready LEDs turn on before you release the Go button, you must start the procedure again with step 1.
The printer's LEDs begin cycling. The cold-reset process runs until completion, and the printer returns to the ready state.

Network reset A network reset changes all network system parameters in NVRAM to the factory defaults. During the network-reset process, all button presses are ignored.
Use the following procedure to perform a network reset.
  1. Turn off the printer.
  2. Simultaneously Press and hold the Go and Job Cancel buttons.
  3. Turn on the printer and continue to hold the Go and Job Cancel buttons for approximately 10 seconds, but no longer than 20 seconds. During this process, the Attention light turns on.
  4. Release the Go and Job Cancel buttons. The Attention , Ready , and Go lights begin cycling from front to back. After the network-reset process is complete, the device returns to the ready state.
    If the Attention and Ready lights illuminate before you release the Job Cancel button, start again at step 1.

Now connect the netowrk cable and wait for 5-mins. After that print a configuration page and confirm the IP address.

- Nikhil

Jul 09, 2008 | HP LaserJet P2015dn Printer

1 Answer

Blinking clean light


replace the dishwasher thermistor if it didn't work than replace the computer board.

May 09, 2008 | Kenmore 16602 / 16604 / 16609 Built-in...

Not finding what you are looking for?
Jenn-Air 24 in. JDB1250 Built-in Dishwasher Logo

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jenn-Air Dishwashers Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Jenn-Air Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...