HP LJ 4200 does not lift the paper deck, but goes to ready state

setting and paper hand ling and set paper tray 3 .if not show check tray connector .

This error can be caused by the following:

1. Fuser that is close to end of life. Maximum print quantity is 225,000 pages.

2. poor quality paper, very thin paper never feeds well and will jam.

3. Printing an image that is almost entirely black can cause the paper to buckle before entering the fuser.


Try different paper to see if that resolves the problem.

If its connected through net work try with lj 4200 drivers..

Please get the correct driver here : www.printcountry.com/drivers.asp
www.opendrivers.com/.../printers-free-driver-download.html
www.driversdown.com/driverslist/r_4_1.shtml
Regards, Jay__9iujgt4

Is the jetdirect card part number a 615n? If so, replace it with a 620N. The 615 cards were bad from the get go. Hp recalled them for about a year providing free upgrades to the 620.

This error message indicates a lifter malfunction has occurred. When the 2000-sheet input tray (Tray 4) is closed, the paper deck lifts the paper stack until it is just below the feed rollers. Photosensor flag PS34, the paper surface photosensor, determines when the paper stack is lifted into the feed position. When PS34 does not detect paper in the expected time, the printer reports a 66 error. SOLUTION: Follow the steps below to troubleshoot and resolve the issue.

1. Turn the printer off, open and close the tray, then turn the printer back on to see if the error clears.
2. Open the drawer and check for extra paper or items stored on the left side of the tray. This will prevent the tray from lifting due to excess weight or blocking the lift of the tray.
3. Remove all the paper from the tray. Remove the tray guides and reseat them. Verify the guides are not bent or broken.
4. Lift the paper deck manually to verify there are no obstructions in the path.
5. Pull the tray out as far as possible and observe the white bushing on the back right side of the tray. If the white bushing is broken, the tray will not lift properly.

Hi,
This could be a couple of things, easiest thing to try first is to put a different toner cartridge in, something that has already been opened because it would save you from opening a new one. Another thing you can try is sending a cleaning page through the printer to clean off excess toner from the fuser unit. What happens is over time toner builds up on the lower pressure roller of the fuser unit and after being heated and cooled so much the toner starts to flake off on your print outs. Follow these steps to try to clean the lower pressure roller:

To run the cleaning page manually
1.If a duplexer is installed, open the rear output bin.

2.Press check mark(SELECT button) or the MENU button to open the menus.

3.Use (UP ARROW button) or (DOWN ARROW button) to scroll to CONFIGURE DEVICE, and then press

4.Use or to scroll to PRINT QUALITY, and then press the check button

5.Use (UP ARROW button) or (DOWN ARROW button) to scroll to CREATE CLEANING PAGE for the(LJ 4200/4300) or PROCESS CLEANING PAGE if you printer is a(LJ 4250/4350) then press the check mark

6.Follow the instructions on the cleaning page to complete the cleaning process (LJ 4200/4300
only).

7.If a duplexer is installed, close the rear output bin.

This should help clear some of the flaking toner, if not you might have to replace the fuser unit.

Hi,

Take the paper off and place the correct paper size.
If the setting is in A4 paper size please place the A4 size paper.

Thanks

Thiru

hi friends......
shivachadra is here.....just i faced this problem "Attention, Ready, and GO LEDs are on solid"
and i got solution in troubleshooting....just vi refixe the connetion of laser scanner........its the error of comunication between laser scanner and formatter....

60.2
printer error
The tray 2 lifter-motor is not functioning. 1 Turn the printer off and then on.
2 If the error persists, turn the printer off.
3 Verify that the tray 2 lifter wire-harness
is full seated in its connector on the
dc controller PCA (location J93).
4 Replace the tray 2 lifter-driver
assembly. See Tray 2 lifter-drive
assembly.
5 Replace the dc controller PCA. See