Question about Garden

1 Answer

How do iline up blades

The pto belt so the blades don't hit?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • Master
  • 1,917 Answers

The blades should not hit only reason a blade hit a blade is if the spindle bearing is out so check that out see if there worn out should be no movement in spindle bearing side to side

Posted on Jun 07, 2014


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 721 Answers

SOURCE: When I pull up on the PTO lever the blades don't

You have a belt adjustment problem, or a broken belt. Look at the area where the belts are, you will probably see problem immediately. Good Luck

Posted on Jun 14, 2011

  • 6468 Answers

SOURCE: John deer selp propelled blades don't rotate fast enough to cut the grass

is the belt getting tight

Posted on May 07, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a jd170 and as soon as I hit the pto switch the mower dies I just replaced the $40 pto switch and that's not the problem

if the blades turn freely then you are going to have to replace the pto or ignition switch,take the drive belt off,does the pto work?,if not,it is electrical,check switch then pto,then pto safety switch

Apr 21, 2015 | Garden

1 Answer

Can't get enough tension on pto belt

make sure you have the proper belt

Sep 23, 2012 | Garden

1 Answer

PTO not working

You have snapped the shear pin that is in the drive pulley. You have to remove the pulley that spins on it's shaft off and put a new shear pin into it. I have replaced several myself. The shear pin is a protection to prevent costly breaks.

Nov 12, 2017 | Garden

1 Answer

44" Exmark lazer z pto/blade problem

My problem is that I don't know what your problem is exactly.

May 06, 2012 | Oregon Scientific Electric PTO Clutch for...

1 Answer

Hi I have the YTH2348, the problem i'm having is i'm getting a bearing sounding squeal when i have the blade clutch engaged. I noticed before it starts to squeal I'll hear a like loud click and...

if its an elect pto then it sounds like its in the workings of the pto pully

also if its a manual lever that you move to engage the belt, it could be the pully that tightens up the belt and turns the blades, most of the pullies are greaseless and prettymuch throw away

Jul 25, 2011 | Husqvarna Lawn Tractor 48" Deck, 23 Hp,...

1 Answer

When I pull up on the PTO lever the blades don't

You have a belt adjustment problem, or a broken belt. Look at the area where the belts are, you will probably see problem immediately. Good Luck

Jun 12, 2011 | Husqvarna 22 hp 42" Yard Tractor YTH22V42

2 Answers

I Have a push mower and hit a rock and finished the lawn hearing the lawnmower blade hit underneath a couple of times. When the mower went down slope the blade started really hitting the side. The next...

hi there nchernuka

have you checked that the engine to chassis bolts are still tight and the mounts are ok,

have you checked that you havn't bent the pto shaft ( this will be evident if you remove the blade carrier and blades, then the plug and pull the gine over - check wobble ), check that blade carrier is in good condition and the pto woodruff key is ok and the carrier centre pto bolt is tight

check that anything that is under the mower body is still tightly attached and is not getting swung into the path off the blades - ie catcher tounge - metal body brackets etc

i would also suggest you check the feather timming key in the flywheel too especially if it kicks back when you try to start it

cheers have a look

hope it helps pauly46

May 27, 2011 | Garden

1 Answer

I hit a hidden log with the blade and it threw the belt. I replace the belt; however, now when I engage the PTO the engine dies.

Your log did more than throw the belt. Something is not able to turn, so when you engage the PTO, the blades stop the motor. Look for another belt jammed, or a bent spindle or piece of log jammed under the deck.

May 09, 2011 | Husqvarna 24HP 54" Yard Tractor ()

Not finding what you are looking for?
Garden Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2478 Answers


Level 3 Expert

708 Answers

john h

Level 3 Expert

15273 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides