Question about Televison & Video

1 Answer

Humax digi iii

Power supply problem ,have no power going in

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Master
  • 12,223 Answers

Clean the contacts batteries and replace by new ones. Resolder the wires going to the contacts batteries.and try it.
See the picture attached. THE LED must be turn ON, when you hit any key. If doesnot TURN ON, open the remote control and clean the keypads for corrosion, oxide, with contacts cleaner solvent. and try again again
God bless youhumax digi iii - 8ce13ced-93a9-4292-835e-f42b0c9446d8.jpg

Posted on Jul 28, 2013

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I only have one scart outlet on my tv my ariel is in the wall and mthen into my tv but its just picking up tv programmes on my humax recorder and not through my tv

The aerial should first go to the Humax, then from the Humax to the TV. Make sure power-saving is turned off on the Humax, otherwise it will not pass the aerial signal to the TV when the Humax is in standby.

If ypou want to use Humax power-saving, the aerial must be split so that one feed goes to the Humax and another to the TV.

May 19, 2016 | Humax Televison & Video

1 Answer

Screen is grey with dots. No message. Originally stalled on picture. When restarted only grey withe dots came up. Humax only 18 moths old

The later build Humax products have some first models good and now oft poor ventilation slots that is better to open secure to release better the warmth. first

Second is the power supply capacitors there are not much capacitors insite that braun power supply i have today repaired a humax 5000c look the pictures the vent slots are now open and 6 capacitors are replaced (only neccesary for power supply) what was 10 v is now 25 v and 25volt are now 35 volt parts 680 mf replaced for 1000mf 82 mf for 100 mf
Thats all what is neccesary to repair the humax POWER SUPPLY

BUt if that your model is not 24 months old you will have warranty on hidden defects because its to young . because it could be another defect but 88 percent its the powersupply .


Apr 21, 2016 | Humax Televison & Video

1 Answer

Problem with Humax 5400Z power supply

Satcure can provide a repair kit for this model:

Apr 14, 2014 | Humax Televison & Video

1 Answer

Digi box broken and I want to get all the films off the hard disk

no, sorry. short of ripping the hard drive out and using some data recovery method on it there won't be much you can do to save those shows.
it is very difficult nearly impossible to move shows from one device to another because of all the copy right rules.

Nov 18, 2013 | Humax Televison & Video

1 Answer

My humax has gon dead

Check the fuse at the main power supply regulator. If found burned, check and replace faulty component/s at the power supply regulator section. If you are not handy, contact any experienced service technician.

Jun 08, 2012 | Humax 22 in. LCD TV

2 Answers

My Digi 002 Rack is "Clicking" (the actual unit).

First thing to do is a hard reset. Merely unplug the power cord for 4 hours, then power up again.In order to dissipated the remaining current stored in the memory and disconnect all unit connected.


Feb 08, 2011 | Digidesign Digi 002 Rack FireWire Pro...

1 Answer

On turning on my humax Foxsat-HDR shifts to standbgy (red light) just when I hope it is going to stop Boot and begin... Please help!


Your power supply board is dead, u know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like, to buy a whole refurbish power supply board for the replacement.
Hope this help in solving the problem.....

Nov 02, 2010 | Humax Televison & Video

1 Answer

How can i fix the humax IR free the reciver not working no LED power light

when pluged to a power supply it click but does not display power

Oct 14, 2010 | Humax HFA100 DTV Receiver

1 Answer

Humax 5400 satellite receiver ,power suppl problem

Dear Robert...

I think the problem with my humax 5400z is similar to yours.

Both 5400 & 5400z have the same power supply unit.

I just solved it this evening by changing C9.

It's a 1500 μF 10V electrolytic capacitor. Be careful not to reverse the polarity my friend.

If you have problems to find the capacitor just e-mail me at and I'll send you pics showing the location of that C9 capacitor on tthe psu board.

Hope this could help you.

Good luck.

Ramez Lebbad.

Dec 04, 2008 | Audio Players & Recorders

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74136 Answers

Cindy Wells

Level 3 Expert

5105 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides