Question about Cobra Radio Communications

Open Question

Astatic cb cobra mic deep diagram

I needto sauder the wires back to the mice that gos to the mic to the cobra cb

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: The wires came of the

if you have a cobra radio with four pin input and a turner road king 56 it goes like this. pin one shield and red wire,pin 2 white,pin 3 blue,pin 4 black and tape up the yellow wire it isn't used. the numbers should be on the plug if not look inside your jack on your radio. hope this helped

Posted on Dec 18, 2008

Ad
  • 1 Answer

SOURCE: cb mic wiring

I have a browning golden eagle mark II. It has a two pin mic plug. I would like to hook up a astatic power mic to it. Anyone have an answer?

Posted on Jan 24, 2009

  • 1 Answer

SOURCE: Mic wiring diagram

Want to wire cobra mic to a uniden washington radio

Posted on Mar 27, 2009

  • 24 Answers

SOURCE: mic wiring diagram 4-pin

try http://www.cbtricks.com/
they have mic wireing diagrams

Posted on Jul 14, 2009

  • 905 Answers

SOURCE: Installing an Astatic Echo Board in a Cobra 148

There should have been instructions that came with your reverb board. You are going to need to drill another hole in the case of the radio, or find a control where you can install a dual control knob onto.

Your reverb board is likely going to need 8v, so you will need to locate that off the logic board, likely from the frequency synthesizer. The the audio lines from the mic, or the output of mic amp, are going to be redirected to the reverb, and the output of the reverb feed back to where the wires were removed from.

If I recall correctly, the 148 is a bit of a bear to work with, not much room inside. You will likely have to get creative in placement of the reverb board itself. Make sure to wrap well so that it doesn't get tossed around and break something inside.

Posted on Sep 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

5 pin astatic corba cb mic


take the mic plug connector an check the wireing that broke off and just rewire it the same way

Jul 27, 2013 | Cobra Radio Communications

2 Answers

D-104 wiring to a cobra cb


Find your radio on this page and then look at the wiring diagrams

Oct 11, 2012 | Astatic D104 T - Ug8 Crystal Microphone...

1 Answer

I need the wiring for the mic


Hello,
Here is the wire diagram for several common mics in relation to a 4 pin CB. Most recent 4 pin CB's such as Midland, Cobra, Connex, Uniden, etc can use 4 pin mics. The wiring is actually depending on the mic rather than the CB so long as the CB's are 4 pin as well. Once you go back to late 80's the 4 pin design was a little different. Anything new it is simpler.
Stock Mic 1- Shield (Ground) 2- Yellow (Audio) 3- Red (Transmit) 4- White (Receive)
Astatic - 4 wire 1- Shield 2- White 3- Red 4- Black
static - 6 wire 1- Shield & Blue 2- White 3- Red 4- Black Yellow NC

Daiwa EM-500 Cobra CA Series 1- Shield & Black 2- Red 3- White 4- Blue
Galaxy DC-521S - 4 wire 1- Shield 2- Yellow 3- Red 4- Black
Galaxy CB-660EI 1- Shield & Black 2- White 3- Red 4- Blue
Sadelta 1- Shield 2- White 3- Brown 4- Green
Turner RK56 Road King 1- Shield & Red 2- White 3- Blue 4- Black Yellow NC
Regards, Tony

Apr 07, 2011 | Connex Radio Communications

1 Answer

I have an astatic 4 pin d104m6b amplified


Hello there
Nice mic i have 3 of these
here is infornation that you can use to get the diagram i like the first link a lot better though it is in full color Ok just look belowtis post and it will be there ok? I hope that this is very helpful for you
Best regards Michael
Repairing the D
These Astatic D-104 microphones are all vintage. ... Doing so will reveal the
simple wiring and the wiring diagram, pasted to the plate on the inside. ... http://www.k3hkr.com/D104_repair.html - 4k - Similar pages I am needing the wiring description for the astatic d104 - FixYa Oct 24, 2009 ... HELLO THERE The silver eagle d104 is wired just the same as the knight ...
astatic echomax 2000 unilli eagle wiring · wiring diagrams for ... http://www.fixya.com/support/t3271236-am_needing_wiring_desc... - 125k - Similar pages

Nov 17, 2009 | Cobra 25 LTD 40-Channels Base CB Radio

1 Answer

I have a Cobra 21- 23 channel CB and the wires pulled out of the plug. The mike wire has red,yellow black,blue,whiteand a ground. My plug has only four prongs to solder to. What four colors do I use?


Hello there
Here is the diagram for you
Cobra 29LTD, 29LTD ST, 29WX ST
Documentation Project
CBTricks.com

TIPS:
You need to have Acrobat Reader version 5 or newer installed to view the files with pdf_1.gif icon.
If the files with jpg.gif or gif.gif icon will not display see the Site FAQ for help on printing, viewing and using this information.
25ltd_st_sm.jpg
Click Picture to See Close-up
cobra_29ltd_st_29wx_st_side.gif 29LTD ST Owners Manual pdf_1.gif
29WX ST Owners Manual pdf_1.gif
DIAGRAMS
29LTD ST Schematic Diagram pdf_1.gif
29LTD ST Schematic Diagram gif.gif
29WX ST Schematic Diagram pdf_1.gif
WX Schematic Diagram pdf_1.gif
29LTD, 29LTD ST, 29WX ST Factory Service Manual pdf_1.gif
Page 1 to 11
Page 12 to 34
29LTD Factory Service Manual pdf_1.gif
29LTD
29LTD Schematic Diagram pdf_1.gif
29LTD Schematic Diagram jpg.gif
29 LTD Classic Schematic Diagram pdf_1.gif(Courtesy of Rick Jackson)



Mic Wiring
Stock
1- Shield
2- Audio
3- Transmit
4- Receive
Astatic (4 wire)
1- Shield
2- White
3- Red
4- Black

Astatic (6 wire)
1- Shield & Blue
2- White
3- Red
4- Black
Yellow NC
Daiwa EM-500
Cobra CA Series

1- Shield & Black
2- Red
3- White
4- Blue
Galaxy DC-521S (4 wire)
1- Shield
2- Yellow
3- Red
4- Black
Galaxy CB-660EI
1- Shield & Black
2- White
3- Red
4- Blue
Sadelta
1- Shield
2- White
3- Brown
4- Green
Turner
1- Shield & Red
2- White
3- Blue
4- Black
Yellow NC

Nov 17, 2009 | Cobra 29 LTD CB Radio

2 Answers

What is different about Galaxy 4-pin mic wiring? My Astatic desk mics work great on my two Galaxy radios but won't allow recieve audio on my other various radios that are also wired for "standard" 4-pin.


i have a cobra mic i am trying to wire to a 4 pin galaxy saturn. What wires do i use and where do they go. i gava blue, red, white, black and ground (copper colored). i cant find any help anywhere HELP!!!!

Sep 05, 2009 | Cobra Radio Communications

5 Answers

Cb mic wiring


I have a browning golden eagle mark II. It has a two pin mic plug. I would like to hook up a astatic power mic to it. Anyone have an answer?

Oct 07, 2008 | Magnum DeltaForce CB Radio

Not finding what you are looking for?
Radio Communications Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cobra Radio Communications Experts

AnyMHz.com
AnyMHz.com

Level 2 Expert

500 Answers

Brad Brown

Level 3 Expert

16174 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Cobra Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...