Question about Pride Mobility Health & Beauty

Open Question

Need off board charging solution advice

Im trying to find a way to charge the batteries themselves with the provided standard scooter charger with the male xlr 3 prong end. i was wondering can i make or buy a connection piece with a female xlr end split to two female 12 volt quick disconnect ends. the whole idea is to be able to bring the batteries in my house(which is easier for me) to charge so i dont have to have them connected to the scooter and bring the whole thing in the house. i wish i can post pics.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 20 Answers

SOURCE: 2000 Ranger seat belt female end will not except male end

LOOK INSIDE THE FEMALE RECIVER AND MAKE SURE THERE IS NOTHING IN THERE. EVEN SOMETHING SMALL CAN MAKE IT SO THE RECIEVER WONT CLICK INTO PLACE

Posted on Nov 27, 2008

Ad
muttandjeff
  • 359 Answers

SOURCE: Charging Canadian battery tools in Europe

http://www.220converters.com/ GO TO THIS WEB SITE AND YOU CAN FIND ALL THE CONVERTERS YOU NEED ALSO READ THE NOTES ABOUT WHAT YOU NEED TO TAKE WITH YOU BATTERY AND POWER WISE . HAPPY TRAVELS AND HAVE A GOOD TRIP

Posted on Jan 12, 2009

  • 118 Answers

SOURCE: Garmin 650 won't hold charge in car -- same problem

Check power at the 12volt outlet to insure that you power is on at the connection. Try using a 12 volt convertor in the house to check the cord used in the vehicle.

Posted on Jul 23, 2009

  • 23 Answers

SOURCE: electric mobility scooter says charge is full but won't run

This sounds she has tripped her circuit breaker. It works just like the one on your house, when you ask too much of it it suddenly goes 'pop' and seems to be dead.

Looks like you have the same scooter as mine, it should be a little white button on the back of the base. If you follow this link, it will give you a pdf version of the older model pride victory manual, (Mine is a three, they are up to about 10!) See fig. 8 on page 20 and 'Circuit Breaker' on page 21. Also, Page 33 has the troubleshooting info. Hope this helps.

http://www.rentascooter.com/downloads/_manuals/pridemobility/Pride%20Victory%20Owner's%20Manual.pdf

Posted on May 06, 2010

Ironfist109
  • 3018 Answers

SOURCE: I need a replacement for


Regards, Tony

Posted on May 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2 Prong Battery Charger


800-255-0285 Leisure lift / Pace saver ask for tech support.

Mar 28, 2016 | Health & Beauty

1 Answer

Hooked up charger sparked melted the plug


Change the XLR PLUG ( three pin male or chassais female are easily found on the internet. Always plug the carger to the mains supply last and remove the mains end plug first when unplugging.

check for shorted wiring inside the XLR plug

Apr 05, 2014 | Pride Victory 4 Wheel Mid-Size Electric...

1 Answer

Convert off board battery charger to work on rascal scooter


It has been done before, but you will violate the safety to do that and anything that happens with this scooter will be your fault! You will need a female electrical part for an XLR Plug to make it so the Male end from the charger will plug in. after wiring the Female connector and plugging the charger in the scooter will run while the charger is plugged in. This can cause safety problems.

Apr 03, 2014 | Electric Mobility Health & Beauty

1 Answer

Micromax x272 charging show but not charging


Hi, so it telling you it's charging however the scooter shows no charge once the charger is disconnected ???

1. First of all , is it possible to try another charger ? or test on another scooter.

2. If the charger proves to be okay, it's starting to look like the fault is with the batteries themselves, batteries can fool certain chargers into thinking they being charged when it fact the resistance inside the batteries have become too great.. They need replacing,...

3. Another issue could be the charger socket or the charging circuit to the batteries..
( is there a fuse ? )

Regards
Rob

www.gewizrepairs.co.uk

Jan 09, 2014 | Pride Line Rally Scooter 3 Wheel Viper

1 Answer

Charging schematic for pride scooter


red + goes to pin 1, black - goes to pin 2 and jumps to pin 3

Dec 29, 2013 | Pride Rally 3 Wheel Scooter

1 Answer

I need to know how to charge the batterie om my sisters merits wheelchair,i do not know how to plug it up,,or if the charger is located on the frame someplace or if its freestanding.plain and simple i do...


sking the off board charger is a 5 inch by 3 inch rectangular box with a power plug on one end and a round silver 3 prong plug on the other. The charger plugs into the charger port located under the front of the joystick. Plug the charger plug into the joystick and then into the wall socket. When it is fully charged the light on the chrager will turn from yellow to green. Unplug the power from the wall socket first then unplug from the joystick In ither words always have the charger unplugged when you plug the charger up to the chair Now if the chair has an onboard charger there should be a power cord that just plugs into the chair usually somewhere in the rear of the chair all you have to do is plug it into a wall socket and charge away Hope this helps you

Mar 10, 2011 | Electric Mobility Merits Electric...

1 Answer

I have a superlu pra-h7a. I also have a cable that connects to the bottom via a three pronged male plug with with a female connector on the other end. i have not used this in years, and can't remember how...


You need to connect it to a mixer first and from there to an amp/speaker combo. This microphone needs phantom power and you can only get it via the mixer. Also, you can control the volume via the mixer. Depends on what kind of speaker you have (active or passive) you will need an amplifier. If you're trying to plug it into a guitar amp, it won't work without a mixer. Plug the 3-prong xlr male cable into the input of the mixer. The 3-prong female xlr end goes into the mic.

Oct 08, 2010 | Superlux PRA-H7A Professional Microphone

1 Answer

How do i charge my scooter its not charging i have brought 2 more now they are flat


Rangi It sounds like its a charger problem rather than a battery problem but if the charger is not working then you'll end up with battery problems too. Vicious circle huh? Try to locate a friend or someone with a scooter or power chair that has an off-board charger and borrow it for a few hours. Charge your scooter with it and see if all the lights are lit up on your scooter's battery level gauge. if they are then you'll have to locate another charger. You can see if your local provider has an extra they will sell you or have them order you a good 3 or 4 amp off-board charger with an on/off switch. Hope this helps you

Sep 27, 2010 | Health & Beauty

1 Answer

Jassy 1103, will not start charging the battery.\r...


the 1103 uses an onboard charger. Charger's life span is about 3 years; some fail in 6 months, some in 6 years keep in mind. You can charge the 1103 using an offboard charger which are available for about $50.00 on Ebay. Search for electric wheelchair charger. You want one that has a 4 to 6 amp rating.

The offboard charger has a 3-prong connector on one end and the other plugs into a grounded wall outlet. Plug the charger into an outlet and the three prong connector into the female three prong connector located at the bottom front of the joystick. Give it a good overnight charge and it should be back up to snuff in the morning.

May 21, 2010 | Pride Jazzy 1103 Ultra Standard Power...

1 Answer

Jazzy Select 6 Indoor Power Wheelchair: how to charge...


The Jazzy Select 6 requires an off-board charger. Plug the charger into a grounded outlet; preferably one that doesn't have other large loads on the circuit like refrigerator, freezer, microwave, etc. The male 3-prong XLR connector coming off the other end of the charger plugs into a female XLR connector which is on the joystick control's bottom-rear. Charge it overnight after each days use, and at least once each month overnight. You should get 2-4 hours of use from the chair at top speed with a 200 pound driver, depending on terrain and climate. If it isn't holding a charge, you will probably need two new U-1 type gel sealed batteries that run about $120.00 or so each. Make sure you test the old batteries first at a knowledgeable battery shop. These are deep cycle batteries and require a special testing. If the batteries are good, then your charger isn't charging. Search EBay or other online sites for a wheelchair charger in the 4-6 amp range. They can be found for about $45.00 or so. Pride will charge you a lot more.

May 18, 2010 | Pride Jazzy Select 6 Indoor Power...

Not finding what you are looking for?
Health & Beauty Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pride Mobility Health & Beauty Experts

Robin Hill
Robin Hill

Level 3 Expert

1271 Answers

Jeff Tilburn
Jeff Tilburn

Level 3 Expert

1105 Answers

Scooter Doctor
Scooter Doctor

Level 3 Expert

401 Answers

Are you a Pride Mobility Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...