Question about HP LaserJet P2055d Printer

Open Question

Bad flash burn power cycle - HP LaserJet P2055d Printer

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 jeep wrangler self diagnosis. The check engine light flashes 10 time, what does this mean? Thanks


the CEL glows for errors running.
and flashes as the operator guide warns you.?
the flashing means, the fuel is way too rich and that flashing means your burning up expensive cat converters.

says, drive gently to auto repair shop too. and dont pull a trailer.
the operators guide is still free, why not read it?
thare she be...mate.... watch out for sharks in the water..

http://www.jeep.com/en/owners/manuals/

we use a scan tool, and scan the PCM it will have CODES
called DTC errors, and are one part of a big clue as to why its failing. (like P0300s)
in fact ever get a tuneup in last 9 years, at least spark plugs?
cant burn fuel with bad spark on mr, otto cycle engines.

Nov 25, 2015 | Jeep Cars & Trucks

1 Answer

Bad flash burn power cycle


sounds like a short across the mains input on the power supply/ or triacs shorted out on fuser driver pwb,
before replacing the power supply (needed) you may also want to replace the fuser unit assembly as a whole as the problem may well have originated from here. ( I would suggest at this point if your toner supply is low for this machine -that it is just as cheap to replace the machine as it is to replace the power supply fuser and toner

Jan 22, 2014 | HP LaserJet P2055d Printer

2 Answers

The machine won't power up. The green light on the PS flashes. What does this mean? If I disconnect the large plug from the mother board the green light will come on steady. Plugging it into the mother...


Can you tell if the flashing is a pattern. count the flashes ( long and short) in a cycle. This will provide an error code to hopefully discover the problem.
You may also try removing and reseating the RAM and Video card, blowing out the connectors with compressed air before reseating.. Also look closely at the components on MB for any signs of swelling, leaking, burning etc. I suspect the MB.

Nov 11, 2010 | HP ATX-300-12Z (ATX30012ZBD) 300-Watt...

1 Answer

The "clean" button is flashing & none of the other cycles work.


heated dry and high temp wash
toggle till all the lights light up
then hit cancel
you should be able to turn dishwasher back on
you probably have a bad heater
is it flashing 7 times
take kick panel off and look to the rear of the dishwasher
is anything burned
if the clean light keeps blinking replace your heater

Feb 09, 2010 | Dishwashers

1 Answer

Furnace blower blows cold air


It is possible that you did not set the new blower on the proper speed. Black wire is high. Blue is medium. Red is low. If the fan is operating to slow it can run to hot and trip the high limit control. Make sure the filters are clean. When the old motor went bad, the problem might not have been discovered rite away your high limit control might need to be changed.
Also anytime you work on a furnace you can kick up some dust. Always clean the flame sensor.
Good Luck
HVAC Teacher

Mar 08, 2009 | Honeywell Power Humidifier: Furnace...

3 Answers

Generator is burning oil and choking out


You have/had too much oil in it. After it is brought down to proper level, it may have to burn the oil that is in areas that it should not be in. Another thing that may cause this, is a dirty air filter, can cause enough suction to pull oil around valves, and other places a clean filter will not. It may have oil in the filter too.

Dec 19, 2008 | Briggs & Stratton Power Products 5,550...

1 Answer

Monitor flashes


If the power button flashes, You probably have a bad power-inverter board thats needs to be refurbished due to burned out capacitors and possibly a transistor or two.
If the screen flashes and the power button stays steady, it could be the same thing or a bad bulb in the screen.
Fran

Sep 30, 2008 | Gateway FPD1975W 19" LCD Monitor

2 Answers

Frigidaire gallery series FDB125ORES1 wash light blinking, dishwasher won't cycle on.


The lights flashed on mine for about three months before smoke started to pour out of it during the drying cycle. It nearly burned my house down.

Aug 14, 2008 | Frigidaire 24 in. FDB1050RE Built-in...

1 Answer

"howling" noise during spin cycle (still there after changing burned off belt)


Travioso, there was two service flashes out on this model concerning the seal and bearing which means they had an issue with this washer. The howling noise you are hearing is the bearing and will need the new designed triple seal and bearing kit. This should be covered under your warranty, I believe it is 5 years. The numbers for the service flashes are TDL-0048A-B. Call Maytag and inquire about these service flashes, these should be covered. Catriver.

Jul 25, 2006 | Maytag SAV5701A Top Load Washer

Not finding what you are looking for?
HP LaserJet P2055d Printer Logo

Related Topics:

355 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Seeker5211
Seeker5211

Level 3 Expert

1089 Answers

kakima

Level 3 Expert

102366 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...