Question about Konica Minolta Cameras

Open Question

How to resolve the problem - please wait now adjusting on CPP650

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i open my facebook,it says 'Sorry, we are experiencing temporary technical problem, please check back later.'how to resolve it.


there's no solution for that. you just need to wait until issue is resolved. facebook is always doing their upgrade.

Jul 25, 2011 | Facebook Social Network

1 Answer

Color recently changed and I cannot get it adjusted properly. Picture goes in and out.


Please do the following steps:

  1. Turn on the television.
  2. Please wait approximately 40 seconds for your TV to completely start up.
  3. On the TV remote control, press and hold the UP ARROW button.
  4. While holding the UP ARROW button, press and release the POWER button on the TV set. (The button may be on the front, top or side of the TV.) NOTE: The TV may turn off and then back on.
  5. Release the UP ARROW button.
If the issue does not resolve, please follow these steps:

  1. Turn off the television. IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
  2. Unplug the television power cord from the electrical outlet.
  3. Let the television remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
  5. Turn on the television.

Feb 27, 2011 | Sony FD Trinitron WEGA KV-36FS120 36" TV

1 Answer

How do i fix error code 20100


Code 20100 means the Wii is having connection problems with your WiFi. Nintendo says:

Error Code: 20100

  • There could be a temporary issue with the Nintendo Wi-Fi Connection servers. Please wait a few hours and try again.

  • If after waiting a few hours and the problem has not resolved, there could be a problem with your home connection. Try the following:

    1. Ensure your home internet connection is working properly. Use a PC that is attached to your home router and visit a website that you have not been to before, in order to check that the connection is currently working.

    2. Try adjusting the "Channel" your wireless router broadcasts on. We highly recommend setting your wireless router to either channel 1 or 11. This can potentially increase stability. For information on accessing your router's settings, click here to select the brand name and model number of your router (if available).

    3. Within the Wii's system settings, erase the current connection file you use to connect your Wii online, and set up a new one. To do this, access the "Internet" option from the Wii settings. For step-by-step instructions, click here.
    If you are still receiving this error code after waiting a few hours and trying the steps above, please call 1-800-255-3700 for assistance.

Dec 01, 2010 | Nintendo Wii Console

1 Answer

Printer will not print from computer


Question : How do I resolve the error code 3813 "Firmware assert" (all-in-one printer)?
Answer : To resolve the error condition:

  1. Disconnect the power adapter from the printer.
  2. Wait 30 seconds to allow the printer to reset.
  3. Connect the power adapter to the printer. Turn the printer on if necessary.
  4. Wait until the printer is ready to use.
If the error condition continues, contact Kodak.

See also here and here.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Aug 31, 2009 | Kodak EASYSHARE 5500 All-In-One InkJet...

1 Answer

A message in the monitor saing waiting for automatic adjustment


you can try to solve this problem eith you're graphic driver program like nvidia control panel. i resolve this messing with "adjust desktop size and position". i hope this help!

Mar 25, 2008 | HP Compaq FP5315 15" LCD Monitor

1 Answer

Hitachi 43fdx15b


Try this procedure:

Adjust the green & blue CRT screens to match the red. Go into your picture menu adjust, turn color all the way down to a black & white picture. Now adjust each CRT screen so that you end up with a true black & white picture. Then adjust each focus control to get a sharp picture, and adjust each CRT focus one at a time for clarity by covering the other two up. Then go back into picture adjust and turn color half way up, you should see a better picture.

If you cannot get the blue & green to even out to a black & white screen you have other problems such as faulty CRT card on back of tube or it could even be that the video IC is faulty. If this is the case, then you may have to get a competent local technician to check the TV and get the necessary parts replaced. It could set you back between $200-$400, depending upon how many components need replacing.

You can also try a hard reset..Unplug all cables, including power from the back of TV. Wait for 4 hrs and reconnect them. Try and see if it works now.

Hope that helps...Should you have any further questions, please feel free to post them here.

P.S. Before you assign a rating, please make sure that the issue is resolved or you are satisfied. If not, please post back as to what you did, and/or any other questions you may have, and I will try to assist you as best I can. Please do not assign an ‘Inappropriate’ or ‘Thanks for trying’ rating if your issue is not resolved after the first response itself, as sometimes a bit of to and fro dialogue may be necessary before we can find a fix or an answer to your query.

If you find that the solution/answer I provided led you to, or resulted in a fix, please close the ticket with a FixYa! or Helpful rating. I would be very grateful for your show of appreciation.

Thank you for using FIXYA!

Cheers!
IrishDruid

Feb 05, 2008 | Hitachi 43FDX15B 43" Rear Projection...

1 Answer

Shutter speed


I've experienced the same problem, I take out the battaries and wait for a minute or so, and usually it resolves the issue

Jan 19, 2008 | Canon Rebel XT / EOS 350D Digital Camera

1 Answer

43FDX15B has blue lines on the screen somtimes


Try this procedure:

Adjust the green & blue CRT screens to match the red. Go into your picture menu adjust, turn color all the way down to a black & white picture. Now adjust each CRT screen so that you end up with a true black & white picture. Then adjust each focus control to get a sharp picture, and adjust each CRT focus one at a time for clarity by covering the other two up. Then go back into picture adjust and turn color half way up, you should see a better picture.

If you cannot get the blue & green to even out to a black & white screen you have other problems such as faulty CRT card on back of tube or it could even be that the video IC is faulty. If this is the case, then you may have to get a competent local technician to check the TV and get the necessary parts replaced. It could set you back between $200-$400, depending upon how many components need replacing.

You can also try a hard reset..Unplug all cables, including power from the back of TV. Wait for 4 hrs and reconnect them. Try and see if it works now.

Hope that helps...Should you have any further questions, please feel free to post them here.

P.S. Before you assign a rating, please make sure that the issue is resolved or you are satisfied. If not, please post back as to what you did, and/or any other questions you may have, and I will try to assist you as best I can. Please do not assign an ‘Inappropriate’ or ‘Thanks for trying’ rating if your issue is not resolved after the first response itself, as sometimes a bit of to and fro dialogue may be necessary before we can find a fix or an answer to your query.

If you find that the solution/answer I provided led you to, or resulted in a fix, please close the ticket with a FixYa! or Helpful rating. I would be very grateful for your show of appreciation.

Thank you for using FIXYA!

Cheers!
IrishDruid

Jan 14, 2008 | Hitachi 43FDX15B 43" Rear Projection...

1 Answer

Please wait


try to clean loading sensors

Jun 03, 2007 | LG RH-4820 DVD Recorder

Not finding what you are looking for?
Cameras Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Cameras Experts

kakima

Level 3 Expert

102366 Answers

Greg Cann
Greg Cann

Level 3 Expert

1114 Answers

Willem.
Willem.

Level 2 Expert

359 Answers

Are you a Konica Minolta Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...