Question about GE AHG50LB / AHG50LD Dehumidifier

Open Question

GE dehumidifier p1 code

My GE dehumidifier will run for a few hours, and then go into P1 error code, will defrost for 30-60 minutes, then work again for a few hours, then go back into P1. We have never had this problem until this year. We took the filter out and cleaned it, wasn't bad at all. Any thoughts?

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
fridgetech
  • 473 Answers

SOURCE: GE AHH40LH DEHUMIDIFIER

Either the humidistat is bad and not letting the unit cycle off, there isn't enough humidity in the air, or the condensor coils are too dirty.

Posted on Nov 16, 2007

Ad
  • 185 Answers

SOURCE: My GE Dehumidifier fan is working fine, but the

a dehumidifier can only remove water from the air that is humid. have you checked the humidity of the room ti see if it is high or low?

In the winter the average room air is sometimes so dry that one have to add water with a humidifier.
did you check if this is not the case?

Posted on Jan 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is wrong with a Westpointe dehumidifier when it stops removing water and displays P1? It will run this way for hours and kick in and work briefly once in a while on continuous.


Usually the P1 error indicates that dehumidifier needs to be defrosted. The unit has detected ice build-up on the condenser coils.

Unplug the dehumidifier for several hours. Then plug it back in. If the problem recurs, check that the fan that blows air across the coils is working properly. Make sure that the room is not colder than the operating range of the dehumidifier. If the problems continues to occur, you may have a refrigerant leak in the system. That will require a service call to repair the dehumidifier.

If the unit is under warranty, contact Westpointe. The manual I have for a Westpointe 65 PT dehumidifier, https://www.appliancefactoryparts.com/content/pdfs/136333-1.pdf, indicates the unit is covered through year 5 after purchase for a refrigerant system. For Warranty service, the contact point is Midea Consumer Service at 1-866-646-4332. If the unit is not under warranty, consider whether to replace the dehumidifier.

I hope this helps.

Cindy Wells
(I have seen a dehumidifier develop a refrigerant leak. It constantly froze before the leak was repaired and the refrigerant topped off.)

May 15, 2017 | Dehumidifiers

1 Answer

Blue star Visi cooler subzero error code p1


Amazon.com: Questions And Answers: WHAT DOES THE P1 error code mean??

www.amazon.com/.../ref=ask_dp_dpmw_al_hza?asin...
Amazon.com, Inc.Oct 19, 2014 - Hi David, According to the manual: "P1- Unit is defrosting-- Allow the unit time to automatically defrost. The error will clear after the unit self ...

Jul 26, 2015 | Dehumidifiers

1 Answer

Spt 65 pint error code p1


According to the manual, this code, P1, means that it is in a defrost cycle. I now have the problem that my unit is in the P1 mode as often as it is in the dehumidification mode.

May 15, 2012 | Sunpentown 65 Pint Dehumidifier with...

1 Answer

DDR4010E just bought and set up now a couple hours later the display reads:P1. what does that mean?


P1 is code for defrosting. Once it's done defrosting it should start operating

Oct 29, 2010 | Danby Dehumidifier

1 Answer

What does P1 mean on display?


Danby's Consumer Help Line (1-800-263-2629) is always busy. So, I called their General number: 419-425-8627. The receptionist transferred my call to their Service dept. My call was answered in 2 minutes.

The Service Rep. described the following code for my dehumidifier model (DDR657EE):
P1 = Defrosting: the unit will go into Defrost mode periodically to ensure that the parts are working at the right operating temperature. It should be in Defrost (P1) mode for only a brief period of time. If the unit is in Defrost (P1) mode continuously for a couple of hours (or more), then you should call Danby Service for further assistance.

He had no documentation of a P2 code for my model.

He also described other General Codes (applicable to most Dehumidifier/Humidifier models):
E1 = Not enough water
E2 = Not draining
E3 = Water temperature too cool
E4 = Overflow Switch activated
E6 / E7 = Problem with Temperature Sensor

I hope that helps.

May 16, 2009 | Danby Dehumidifiers

1 Answer

My model is DDR4009EE, after it run for a while, the display changed from RH to "P1",what does "P1" mean?


My Danby DDR657EE shows P1 periodically also. So, I called Danby.

Danby's Consumer Help Line (1-800-263-2629) is always busy. So, I called their General number: 419-425-8627. The receptionist transferred my call to their Service dept. My call was answered in 2 minutes.

The Service Rep. described the following code for my dehumidifier model (DDR657EE):
P1 = Defrosting: the unit will go into Defrost mode periodically to ensure that the parts are working at the right operating temperature. It should be in Defrost (P1) mode for only a brief period of time. If the unit is in Defrost (P1) mode continuously for a couple of hours (or more), then you should call Danby Service for further assistance.

He had no documentation of a P2 code for my model.

He also described other General Codes (applicable to most Danby Dehumidifier/Humidifier models):
E1 = Not enough water
E2 = Not draining
E3 = Water temperature too cool
E4 = Overflow Switch activated
E6 / E7 = Problem with Temperature Sensor

So, if you see P1 periodically (for brief periods), then it would be normal.

Also, here is a link to Danby's FAQ page for Dehumidifiers (which answers some common questions):
https://www.danby.com/faqs.php?cat=12

I hope that helps.

May 11, 2009 | Dehumidifiers

1 Answer

P1 error


Your question needs to be answered in 3 parts:

1) As per the manual for my Danby Dehumidifier (Model DDR657EE), the unit may not turn on immediately when powered On (it may take a several minutes). So, generally, it would be normal in your case.

2) Danby's Consumer Help Line (1-800-263-2629) is always busy. So, I called their General number: 419-425-8627. The receptionist transferred my call to their Service dept. My call was answered in 2 minutes.

The Service Rep. described the following code for my dehumidifier model (DDR657EE):
P1 = Defrosting: the unit will go into Defrost mode periodically to ensure that the parts are working at the right operating temperature. It should be in Defrost (P1) mode for only a brief period of time. If the unit is in Defrost (P1) mode continuously for a couple of hours (or more), then you should call Danby Service for further assistance.

He had no documentation of a P2 code for my model.

He also described other General Codes (applicable to most Dehumidifier/Humidifier models):
E1 = Not enough water
E2 = Not draining
E3 = Water temperature too cool
E4 = Overflow Switch activated
E6 / E7 = Problem with Temperature Sensor

So, generally, if you see P1 periodically (for brief periods), then it would be normal.

3) Since your unit keeps running (continuously) and there is no water in the bucket, then you should call Danby ServiceI for additional assistance - it seems defective for this reason.

I hope that helps.

Oct 31, 2008 | Danby DDR2506 Dehumidifier

2 Answers

P1 error code


Take out your filter and clean it, if its dirty your machine can frost up due to the lack of air flow and will not work correctly. Once you clean it, it should be fine.

Sep 13, 2008 | Danby DDR2506 Dehumidifier

6 Answers

P1 and P2 error codes


Danby's Consumer Help Line (1-800-263-2629) is always busy. So, I called their General number: 419-425-8627. The receptionist transferred my call to their Service dept. My call was answered in 2 minutes.

The Service Rep. described the following code for my dehumidifier model (DDR657EE):
P1 = Defrosting: the unit will go into Defrost mode periodically to ensure that the parts are working at the right operating temperature. It should be in Defrost (P1) mode for only a brief period of time. If the unit is in Defrost (P1) mode continuously for a couple of hours (or more), then you should call Danby Service for further assistance.

He had no documentation of a P2 code for my model.

He also described other General Codes (applicable to most Dehumidifier/Humidifier models):
E1 = Not enough water
E2 = Not draining
E3 = Water temperature too cool
E4 = Overflow Switch activated
E6 / E7 = Problem with Temperature Sensor

I hope that helps.

May 25, 2008 | Danby DDR2506 Dehumidifier

Not finding what you are looking for?
GE AHG50LB / AHG50LD Dehumidifier Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dehumidifiers Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

J.D. Browning
J.D. Browning

Level 3 Expert

2760 Answers

AZBen
AZBen

Level 2 Expert

193 Answers

Are you a GE Dehumidifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...