Question about Exercise & Fitness

1 Answer

Reebok power run treadmill

I have power to the treadmill as the elevation is working and the power light is on on the side of the unit it the display screen won't come on and therefore I can't get belt to work

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 12,223 Answers

Adjust the REED swtich, see the diagram attached.clean it, and tight the connector very well. God bless you
If the problem persist, tight the ribbon cable inside the control panel, and clean it too. Otherwise you have a control panel faultyreebok power run treadmill - 8da47572-fa1c-4850-ad85-b0d8c94bdf71.gif
God bless you

Posted on Jul 23, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 64 Answers

SOURCE: reebok i run treadmill stops working after 10 mins

If everything still works but no belt movement, you motor controller is more than likely shot. If replacing you want to also pay attention to the deck and belt. Sence it sut down while running, it sound it an over heating problem which is usually caused from too much friction between the walking belt and the deck(the board under it) May require lube or may need replacing.

Posted on Jun 08, 2009

keepfituk
  • 11 Answers

SOURCE: reebok i run stopped working after 5 mins power

it sounds like it may be the fuse on the motor circuit board? if you unscrew the motor cover and have a look inside(ensure you have turned the power off) you will see the circuit board and the fuse is in the middle. take it out and have a look to see if it is intact. go to Maplins and ask for a replacement as it is not a standard fuse, it is a 'time delay fuse'.
if this does not resolve the issue, you may need a replacement motor circuit board (around £40) which is very easy to replace. if you need help doing this let me know and ill guide you through it.

Posted on Jan 24, 2010

maxtreadmill
  • 832 Answers

SOURCE: hello,my reebok i-run treadmill belt is not moving

Usually a spark means you have a problem with either the drive motor or motor controller board became damaged. Unplug unit remove the motor shroud physically inspect the motor and board for any signs of arching then replaced the board. Next use a multi meter to check continuity of the drive motor by removing the red and black leads that attached to the board if a reading is much more than 1.0 to 2.0 ohms then your motor is also damaged need to be replaced.

Posted on May 14, 2010

  • 218 Answers

SOURCE: hi i got a reebok i run treadmill power light on

# get a 12-18 volt dc battery fully charged(like one from a cordless drill)
# Make sure it is fully charged, because it won't work if not
# attach the + and - to the motor red is + and black is -
# If the motor turns slightly your motor is ok, if not the motor is bad and would need replaced
# if the motor is ok then your motor controller(the board with the metal) is malfunctioning and would need replaced.

Posted on Aug 11, 2010

ercupa190
  • 12223 Answers

SOURCE: F85's "low speed" error

Dear Sir:
1) Lube the deck belt very well, as your instruction manual indicate for maintenance.
2) Try to Run software calibration after you fix it. For easy diagnose and troubleshooting.
3) The elevation motor can be faulty for lack of maintenance too, again Run the software calibration.

sincerely. God bless you

Posted on Apr 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Reebok i run treadmill is not working.


If you wish to get some details about treadmill repair check the bellow added link.
www.electro-medical.blogspot.com

Jun 28, 2016 | Reebok Exercise & Fitness

1 Answer

Reebok tr2 incline wont work, back of machine starts to rise when you prees the incline up button


1) lube the motor elevation, shaft +gear and adjust the POTentiometer a little
2) see the diagram attached,
3) Run the software calibration for troubleshooting,
4)test the relais for open or faulty coil,and clean the contacts very well
God bless you1_22_2013_5_10_05_pm.gif1_22_2013_5_10_34_pm.jpg1_22_2013_5_11_02_pm.png

Jan 22, 2013 | Treadmill Doctor Reebok S 9.80 Treadmill...

1 Answer

I have a reebok crosswalk rt 5.0 treadmill. I can calibrate the incline and it goes up and down. however when you press the button to raise the incline the incline number will change but the machine does...


Step 1:

see this details and proceed according. God bless you

The SCR lower board is designed with diagnostic LED lights. The LED's are color coded according to

their specific function. Green indicates a properly operating treadmill; the green lights should always

be ON when power is supplied to the treadmill. Yellow indicates a treadmill function. Red indicates a

treadmill malfunction. Here is a list of each LED and what it signifies:

MOTOR (yellow) - The MOTOR LED illuminates when dc (direct current) voltage is sent to the drive

motor. The LED gets brighter when the dc output is increased.

RLC (yellow) - The RLC (R = Reactance / L = Inductance / C = Capacitance) LED illuminates when

the filtering system is properly working. The filtering system includes the capacitor and filter choke. If

there is a short in either component then the RLC light will not come on.

DN & UP (yellow) - The DN and UP LED lights tell us if the elevation DN and UP relays are

functioning properly. When the LED lights, it tells us that the relay has energized and is sending high

voltage (110vac or 220vac) to the elevation motor.

AC PWR (green) - The AC PWR (Alternating Current Power) illuminates when AC line voltage is

delivered to the treadmill. It then passes through the in-line fuse (110)/s(220) and lights the AC PWR

LED.

+12V (green) - When the proper AC voltage is delivered to the treadmill, passes through the in-line

fuse/s, through the full wave bridge rectifier (changes AC to DC), through the transformer (steps down

Step 2:

This the board LED, who control the DC to +12vdc) then the +12V LED lights.
signal for Main Motor+Elevation Motor. You must see, the LED DN+ UP( both will be Lit) in any position down or Up.

2) The RELAY board is designed with diagnostic LED lights. The LED's are color coded according to

their specific function. Green indicates a properly operating treadmill; the green lights should always

be ON when power is supplied to the treadmill. Yellow indicates a treadmill function. Red indicates a

treadmill malfunction. Here is a list of each LED and what it signifies:

AC PWR (green) - The AC PWR (Alternating Current Power) illuminates when AC line voltage is

delivered to the treadmill. It then passes through the in-line fuse (110)/s(220) and lights the AC PWR

LED.

VDC (green) - The VDC LED will light when it receives DC voltage from the DC power supply.

DN & UP (yellow) - The DN and UP LED lights tell us if the elevation DN and UP relays are

functioning properly. When the LED lights, it tells us that the relay has energized and is sending high

voltage (110vac or 220vac) to the elevation motor.

UPSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper display

board to the elevation UP relay. This low voltage dc is what energizes the coil of the relay.

DNSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper display

board to the elevation DOWN relay. This low voltage dc is what energizes the coil of the relay.

BELTSW (green) - This LED will illuminate when the low voltage dc is delivered from the upper

display board to the belt (motor start) relay. This low voltage dc is what energizes the coil of the relay.

SPD (yellow) - The SPD LED flashes on and off (relative to speed) when the speed sensor is

operating properly.

PWM (yellow) - This LED will light when the upper board is sending a speed signal to the PWM.

Both the PWM LED and BELTSW LED must be lit for belt movement.
Finally this this Relay Board, the Each Led will be Lit, for any Relai control for DN down, or UP for elevation Motor. You must clean contact of the Relay with Special Spray(Radio Schack).

With this you must fix it.

Jan 07, 2013 | Reebok Exercise & Fitness

1 Answer

Treadmill Protec Forerunner 3000 E 7 light on (mother control board FH-3545C-E, VER:B2)


Step 1:

you will have two alternatives:

ERROR CODE # 7

E7- 1) Alternative Elevation Motor

1)Cause: Elevation Motor not moving Solution:Check Elevation Motor connection

2)Cause: Elevation Elevation Motor screw binding Solution: Clean screw and lubricate

3)Cause: Elevation Motor Motor out of Range Solution: Check motor out of elevation

4)Cause: E-Motor Potentiometer: Solution: Replace Elevation Motor



2)Alternative:

Display Doesn't Light Up: a)Cause: On/Off switch Solution: Test unit is turned on b)Cause: Insufficient Power Source Solution: Plug dedicated120V, 20Amp Outlet

c) Cause: Line Cord Damaged Solution: Replace Line Cord

d)Cause: Fuse Solution: Check Fuse on MCB

see the block diagram+additional diagrams for troubleshooting and fix it.

God bless you


Step 2:

1_4_2013_6_15_26_pm.jpgelevation motor diagram

Step 3:

treadmill motor control board diagram
1_4_2013_6_16_16_pm.jpg1_4_2013_6_16_30_pm.gif

Jan 04, 2013 | Sportcraft Exercise & Fitness

1 Answer

Treadmill KETTLER PACER error code E7, what I have to do?


see the next steps and fix it. God bless you

ERROR CODE # 7

E7- 1) Alternative Elevation Motor

1)Cause: Elevation Motor not moving Solution:Check Elevation Motor connection

2)Cause: Elevation Elevation Motor screw binding Solution: Clean screw and lubricate

3)Cause: Elevation Motor Motor out of Range Solution: Check motor out of elevation

4)Cause: E-Motor Potentiometer: Solution: Replace Elevation Motor



2)Alternative:

Display Doesn't Light Up: a)Cause: On/Off switch Solution: Test unit is turned on b)Cause: Insufficient Power Source Solution: Plug dedicated120V, 20Amp Outlet

c) Cause: Line Cord Damaged Solution: Replace Line Cord

d)Cause: Fuse Solution: Check Fuse on MCB

Nov 28, 2012 | Kettler treadmill Pacer

1 Answer

Treadmill KETTLER PACER have error E7 when starting run. How to eliminate it?


see the following indications and fix it. God bless you

ERROR CODE # 7

E7- 1) Alternative Elevation Motor

1)Cause: Elevation Motor not moving Solution:Check Elevation Motor connection

2)Cause: Elevation Elevation Motor screw binding Solution: Clean screw and lubricate

3)Cause: Elevation Motor Motor out of Range Solution: Check motor out of elevation

4)Cause: E-Motor Potentiometer: Solution: Replace Elevation Motor



2)Alternative:

Display Doesn't Light Up: a)Cause: On/Off switch Solution: Test unit is turned on b)Cause: Insufficient Power Source Solution: Plug dedicated120V, 20Amp Outlet

c) Cause: Line Cord Damaged Solution: Replace Line Cord

d)Cause: Fuse Solution: Check Fuse on MCB


11_28_2012_3_01_16_pm.gif

Nov 28, 2012 | Kettler treadmill Pacer

1 Answer

I HAVE POWERTREK STRIDER IS NOT WORKING WHAT WILL I DO


see the next causes and remedy and fix it. God bless you

ERROR CODE # 7

E7- 1) Alternative Elevation Motor

1)Cause: Elevation Motor not moving Solution:Check Elevation Motor connection

2)Cause: Elevation Elevation Motor screw binding Solution: Clean screw and lubricate

3)Cause: Elevation Motor Motor out of Range Solution: Check motor out of elevation

4)Cause: E-Motor Potentiometer: Solution: Replace Elevation Motor



2)Alternative:

Display Doesn't Light Up: a)Cause: On/Off switch Solution: Test unit is turned on b)Cause: Insufficient Power Source Solution: Plug dedicated120V, 20Amp Outlet

c) Cause: Line Cord Damaged Solution: Replace Line Cord

d)Cause: Fuse Solution: Check Fuse on MCB


11_29_2012_5_40_19_pm.gif

Nov 13, 2012 | Treadmill Doctor Nordictrack Powertread...

1 Answer

What does E7 mean on Lifespan TR4000i?


see the 2 alternatives that the error code 7 means:

E7- 1) Alternative Elevation Motor

1)Cause: Elevation Motor not moving Solution:Check Elevation Motor connection

2)Cause: Elevation Elevation Motor screw binding Solution: Clean screw and lubricate

3)Cause: Elevation Motor Motor out of Range Solution: Check motor out of elevation

4)Cause: E-Motor Potentiometer: Solution: Replace Elevation Motor



2)Alternative:

Display Doesn't Light Up: a)Cause: On/Off switch Solution: Test unit is turned on b)Cause: Insufficient Power Source Solution: Plug dedicated120V, 20Amp Outlet

c) Cause: Line Cord Damaged Solution: Replace Line Cord

d)Cause: Fuse Solution: Check Fuse on MCB
However RUN the software calibration for diagnostic, troubleshooting and Fix it.

God bless you

Sep 29, 2012 | LifeSpan Fitness TR4000i Folding Treadmill

1 Answer

Reebok v 6.80


what is the problem display, motor elevation, or main motor, Pleae reply inmediately.
However RUN The software calibration for easy diagnose, troubleshooting, fix it.
God bless you

Jul 30, 2012 | Exercise & Fitness

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Howard
Howard

Level 2 Expert

115 Answers

Tom Chichester

Level 3 Expert

34759 Answers

Are you an Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...