Question about Fisher and Paykel Aquasmart wl80t65c

Open Question

Fisher and paykel aquasmart washing machine lid wont lock

The washing cycle won't begin because the machine cannot recognise that the lid is closed

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

JULIANFIX
  • 975 Answers

SOURCE: fisher & paykel (mw511)

check out the DRAIN MOTOR PUMP , its a small motor with 2 hoses connected to it , it could be clogged , need to remove it , inspect inside the impellers for any debri , clean it , re install and try again , hope this helpful AJ

Posted on May 20, 2008

  • 22 Answers

SOURCE: washing machine will not spin or drain

look at my post "eco smart won't drain, smells hot". It could be something stuck in very lowest part fo drainage area. you have to remove the motor on bottom of washer to see into this area and remove blockage.

Posted on Oct 21, 2008

RescueTech
  • 145 Answers

SOURCE: Fisher Paykel washing machine model # GWL15 drips

Hi Dale..
It sounds like you have a leaky inlet valve assembly. The part number is 421029P and is easy to replace. You can get one here:
http://www.fisherpaykelparts.net/ecart/item.php?item_id=266&category_id=56

Posted on Apr 20, 2009

  • 10 Answers

SOURCE: Fisher & Paykel GW612 Top Loading Washing

Hi there
That fault is the pump blocked error (no change in water level).
i have a quick and easy way to solve this problem.

first turn the machine off then tilt the machine back and lean it on something(a chair or wall), look underneath, in the top right hand corner of the plastic outer boul you will see a small pump motor it has a fan on it spin this fan and if it is hard to turn that means there is somthing stuck in the drain pump keep turning the fan and try to free whatever is stuck in the pump, then try the machine on spin again all goin well the object in the pump should come out with the drain water(doing this will not harm the machine) if the object is still stuck you will need to get the water out of the machine (bailing or siphioning will work) and tilt the machine back again and take the wires off the pump and there should be a white tab on the boul holding the pump on pull this tab and twist the pump anticlockwise about a quarter turn(you will need a few towels or a boul or bucket to catch the water) and it should come off exposing the blockage.
Hope this solves your Problem.

Nick

Posted on Aug 03, 2009

  • 159 Answers

SOURCE: No water flow on Fisher and Paykel smartdrive 708 washing machine

Take the lid off,just open it & pull it straight up.There should be a little red button that the lid strikes against unless its a different model,in that case it has a magnetic reed switch under the right hand side of the hob.press this red switch instead of closeing lid,see if it fill with no problem.the lid may not be making good contact with switch..if thats not it then it may be the inlet valve..then you can try the hot,if theres no problem with hot then its the cold valve.

Posted on May 30, 2010

Testimonial: "Very helpful, as I was completely ignorant about the workings of a washing machine. Replied promptly and had a good sense of humour - important in a crisis!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WL80T65CW1. Why is it displaying fault 234 and will not cycle?


Replace just the lid lock assembly to start with and see how it goes. Lids are quite expensive and don't usually need replacing. You can always get a lid later if you still have problems.

Aug 25, 2015 | Fisher and Paykel Aquasmart wl80t65c

1 Answer

Aquasmart lid


Is the lid lock tang on lid broken.
2.9 Lid Lock
The Phase 7 Washer uses the same lid lock that is used on
the Phase 6 series 11 & 12 machines. The difference being is that the lid is now locked for the entire cycle. When the lid is locked the Lid Locked LED will illuminate. Once the spin
has completed, the lock will release and the lid can be
opened. To open the lid during the cycle the
START/PAUSE button must be pressed, the machine will
come to a halt, and the lid locked LED will extinguish.
If the lid is left open, the machine will be unable to lock the lid
and the cycle will be halted. The machine will play a tune
and the lid lock will flash until the lid is closed and START/PAUSE is pressed.
• If the lid-lock fails in the closed position, the locked lid can be forced upwards and out of the
lock. Note: This is the only time in which we would recommend doing this.
• If the harness is damaged, the complete lid lock assembly will need to be replaced.
If the power supply is cut during the spin cycle, the machine will keep the lid locked until the rotor has ceased to turn (3 to 10 secs). Only then will it release the lock. The motor is acting like a generator and allows the lock to stay energized under the bowls inertia.

Mar 16, 2013 | Fisher Paykel EcoSmart GWL15

1 Answer

Fisher & Paykel Aquasmart washing machine makes loud banging noise then stops during rinse/spin cycles


Your Aquasmart machine requires 4 new suspension damper rods & 4 top bands, these are a common problem for AquaSmart machines.

Feb 02, 2013 | Fisher and Paykel Washing Machines

1 Answer

Fisher and paykel aquasmart fault 235


Try cleaning the INLET and the outlet valves, it is possible that the filters are blocked. If not check the wiring harness from the panel, check for moisture within the panel, if so use a dryer to warm off and test. Please estimate before any parts are replaced.

Jan 20, 2013 | Fisher Paykel Fisher & Paykel AquaSmart...

1 Answer

Fisher and paykel model no GW611 washes but won't spin nor lid locks


Sounds like the lid lock has gone bad. Check the wire connections to it and if you should need to order the lock, here is their website.

Nov 05, 2012 | Fisher Paykel EcoSmart GWL15

1 Answer

Washing machine won't go thru spin cycle. Lid lock light flashed some at first, now won't come on at all.


Hi there the lid lock switch is faulty and needs to be replaced - cannot be bypassed unfortunately.

Jul 14, 2011 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

My aquasmart fisher and paykel washing machine flashes up with error 235 about 2 mins after starting


Sounds like the 'lid lock' has shorted out. They're not completely waterproof and have seen pins completely blown out inside them. Should measure 73 ohms (or very close to it) across the terminals. Hope this helps.

Jan 16, 2011 | Fisher and Paykel WL26CW1 Top Load Washer

1 Answer

My Aquasmart WL80T65D washing machine is telling me that it cannot lock the lid - but it is shut and appears to be in place.\r\n Does anyone have any suggestions for this?


Hi just read your posting.Does the machine stop and beep and show an error code in the form of lights on or an error code in an LCD display?Please reply with additional information and I am sure I can help you rectify the fault.Looking forward to your reply.

Oct 10, 2010 | Fisher and Paykel Fisher & Paykel Washer

Not finding what you are looking for?
Fisher and Paykel Aquasmart wl80t65c Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Owen Barnes

Level 3 Expert

867 Answers

marley mcelhinney

Level 3 Expert

490 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...