TEXAS I HAVE A DENON 3000 DVD PLAYER, PURCHASED IN 1998, DISPLAY WHEN TRY ANYTHING SAYS LOCKED, CAN NOT REMOVE

TRY TO FIND DVD PLAYER RESOLUTION SAME TO THE RECEIVER....MAY BE IT WORKING..

The video cables--the green, blue, and red ones must be connected from the video OUT portion of the DVD player to the Component 2 video IN of the Denon. It could be the handshake between your Denon and your television. Do you have anything else to connect to the Denon to see if you get a picture? How are you connecting the Denon to the television? Make sure you have your television on the proper input and check the cables going between it and the Denon.

1. Turn the unit on
2. Press the OPEN/CLOSE button
3. Press CLEAR, 1, 4, 7, 0, CLEAR - "TEST MODE" will appear on the display.
4. Press UP; "00 XX" (XX is a numerical value) will appear on the display. The first two digits are incremented by one, every time you press UP
5. Press the UP key until you see "12 XX" (default is 24) on the display
6. Press 2, 3, ENTER
7. Press UP key again and you will see "13 XX" (default is 23). If it does not say "23", press 2, 3 on the remote and then the ENTER button
8. Press the UP key again and you will see "14 XX" (default is 01).
9. Press 0, 0, ENTER
10. Press RETURN
11. Press CLEAR twice
12. Press RETURN ("END" should appear on the display)
13. Press OPEN/CLOSE

no the problem is at the plasma you will have to change the setting back to the scale range that will accept the signals from the Denon, see Plasma's manual for instructions

Make sure the S-video and the composite cable are not plugged in it the same time from the Denon of at the Plasma

Hello gerrydav, What might be happenening is the refresh rate for your blu-ray is offsync for your preferred display. You should be able to change it by plugging it into another TV and playing around with the settings. If you have further problems please feel free to post again.
Please post what you do and how you did it. I look forward to your posts.

Hi,

Initially, pls try:

• Verify that the tray is empty/no disc in the player;
• Shut down/off with the front panel On/Off button and not the standby;
• Press and hold the Open/Close, Play and Skip Reverse (I<<) buttons;
  
• Maintain pressing on the above buttons and Power-ON the player with the On/Off button, (again while still holding the above buttons till the "Denon 2910" disappears from the display);
• pls wait till LOADING completes and the front panel would display 0:00:00;
• Using the remote control, enter 7, 3, 1, 9, 4, 6, 2, & 8;
• The Denon 2910 will go into standby mode. Soon as it is on standby, pls press the Standby button on the front panel;
• Pls verify region free update by pressing the Stop and Skip Forward (>>I) buttons on the front panel. The display would show “Region_Ax” The x would be the former region number that the Denon 2910 is locked into;
• Should it not work ouot as expected, pls redo all the above steps.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information. Good luck and kind regards. Thank you for using FixYa.

You will have 2 choices here, replace it or have it repaied

Just try to initialize THE plager again. Without cd in the player switch on the power while pressing the Play, Open and Next Track button. On the display it says " initialized" Ready. Frits van Heekesen Nijmegen The Netherlands

you could try this http://www.fixya.com/support/t244156-denon_2910_cd_player_malfunctions or clean the lens