Question about Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Washer will not spin

I have a hotpoint aquarius wms38 when i put a load in it will fill up with water then nothing happens it will not spin then it emptys the water then fill again for the rinse but it will not continue and just stops with the wash, rinse and spin and fast spin lights on. any help would be very graetful t5hanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 209 Answers

Normally i would suggest changing motor carbons for hotpoint washers, but my experience is that the WMA motor armature is weaker than the carbons, normally if there is no connection fault a replacement motor is the answer 9 times out of 10, not a job for the amature

Posted on Sep 02, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Machine does not seem to be filling properly, then does nothing else.


Sounds like you're fill valves are junk which sadly happens allot. This video is very generic but should give you an idea

Jul 06, 2017 | Hotpoint Ariston Aquarius WD420 Front Load...

1 Answer

Hotpoint Aquarius wms38 1200spin Machine fills with water after wash cycle is finished and it is turned off


If the water is coming in after cycle has finished, then it is 1 of 2 possibilities.
1- A faulty inlet valve, replace it.
2-Water is syphoning back from the sink if it is connected to the sink waste outlet pipe, raise washer outlet hose higher up to solve problem

Nov 30, 2010 | Hotpoint Washing Machines

1 Answer

Hi. i have had funny noises during last couple of washes. now washer wont drain programs are responding fine but washer keeps filling up and not draining.water backed up and came out of the drawer hotpoint...


Hi,

Problems with a washing machine not spinning or not draining are often inter related..

If you are having a problem with your top load washer then check out this tip...

Washing Machine does not Pump or Spin
http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you are having problems with your front load washing machine then checkout this tip...

Front Load Washing machine not draining and or not spinning
http://www.fixya.com/support/r4784376-front_load_washing_machine_not_draining

heatman101

Aug 18, 2010 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Please help the washer fills up and turns the


Seems like a blockage or maybe pump worn out. Fill machine and take grey outlet pipe on rear of machine. Place this pipe as low as possible into a bowl. If water flows free from this pipe then your pipes are not blocked and most likely you will need to change your pump. Before you try this just put machine onto spin and ensure this will work when machine is almost empty

Mar 12, 2010 | Hotpoint Aquarius WF220 Front Load Washer

1 Answer

Hotpoint aquarius wf321 when turn on all red light fleshing Problem nothing happenes.


half way through the cycle all the lights start flashing then it makes a loud noise when spinning

Jan 17, 2010 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hotpoint Aquarius 1100 WM63. fills with water...I dont think it is heating water...rarely rotates and spins (saw it once in early stage of J prog only) seems to fill and empty but no rotate or spin....


if it fill with water then stops it is the ellement the machine first fills turns the drum then heats up the thermostat cuts in and the it emptys rinses and spins so if it does not get to temp it will stop or continue to wash forever

Jun 27, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Granddaughter just bought second hand hotpoint aquarius extra wms38 1200 spin .fixed it all up water coming through the ppipes but not in to the machene not filling up or doing anythging any advice please


Soumds like the water inlet valve is not working. You will have to remove the top of the casing and replace thr inlet valve. If the valve is ok then the trouble will be at the programmer. Usually it is the inlet valve.

Jun 09, 2009 | Washing Machines

1 Answer

Hotpoint Aquarius wd440 washer/dryer wont pump out water HELP!


Try unplugging the unit and plug it back in. This may reset the controls.

Jun 02, 2009 | Hotpoint Aquarius WD640 Front Load...

1 Answer

Hotpoint aquarius wf210 g washes but stops at rinse


that is a possabilty, make sure you have water going to cold valves put test bulb on the wires going to valves it should light] close Ire. that means you have current going to valves] get back to me if you can\t sort it

Nov 03, 2007 | Hotpoint Aquarius WD640 Front Load...

Not finding what you are looking for?
Hotpoint Aquarius WMA42 Front Load Washer Logo

Related Topics:

520 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

vince

Level 3 Expert

1211 Answers

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

puggy666

Level 1 Expert

48 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...